Mouse Anti-Slip Tape Elastics Refined Side Grips Sweat Resistant Pads/Anti Sweat Paste Grip Tape Compatible for Razer Viper/Viper Ultimate Gaming Mouse

I use it for my razer mouse and it grips around the mouse just fine. You have to be extra careful because there is no tolerance at all for the sizing of the grips. You have to be able to match the exact edges of the grip to the mouse or else it looks weird. Which is fine by me because I do that anyway for most things but keep that mind if you want to be lazy about doing it. It's very grippy and definitely helps with my gaming sessions and such.

This product is great, fits excellent

Fits perfectly on the Razer Viper Ultimate! I highly recommend it as a solution to the well-known Razer finger grip issue, especially for those whose skin tends to wear down the rubber material on older models. This tape provides a strong, firm grip while covering and protecting the original material on the mouse. It’s an excellent choice for gamers who want to maintain their trusty mouse in great condition. Totally worth it!

I got this to replace the worn out grip on my mouse. Could probably have just stuck it right over the old grip, but it'd been worn down so bad that the new tape just conformed to all the divots and looked terrible. I dug out the old grips and just put these new ones on the bare plastic and it's worked great for ... 9 months so far? The only thing that didn't work as well as I would have liked was the thumb buttons. Just because it's a small contact spot and the surface is curved, the thumb button tape came off after a while, but the main grip has held up very well!

Glad replacement mouse feet exist, gliding is pretty smooth.

This works very well. The fit is very precise, with very tight tolerances (be slow and careful when applying them to the mouse to ensure a good alignment)The stock grip has a variable thickness, while this product has a uniform thickness. However, this product's thickness is PERFECT for the edges of the grip where it meets the body of the mouse, making for a seamless transition from grip to plastic with no ridge or groove. However, the uniform thickness means that areas where the stock grip was thicker become slightly dented feeling with this product, as it doesn't fill those deeper voids in the plastic quite as well as the stock grip. The most notable spot where I can feel a dent is right where my thumb sits though, so it's actually quite comfortable and a non-issue. Maybe even more ergonomic!I found that the stock grip was quite easy to remove by just picking the front corner up with a fingernail, and pulling the grip off the mouse. No heat was needed. I suppose if you have particularly weak hand grip strength, using heat might make it easier, but I had no trouble.Once the stock grip is peeled off, there is a thin foam-like residue left over that must be scraped off before applying this product. I recommend using a plastic spudger or other sharp plastic tool to avoid scarring the mouse plastic (a metal tool would damage the plastic). If you don't have a plastic spudger, add one to your order; they're super cheap, and worth the saved effort for scraping the residue off.When the residue has been mostly cleaned off, use isopropyl alcohol and paper towel to get any remaining bits, and clean off any oils that may be stuck on the plastic.When the surface is prepped, carefully (and slowly) line up the new grip with the back bottom corner of the mouse first, to ensure a seamless fit in that most critical and frequently touched area. For the click buttons, line up the little tab section in the middle first, and make sure you keep it straight as it goes on. Work along an edge, then move inwards to ensure good alignment.I skipped the thumb buttons, as other reviewers had mentioned it wears off quite fast; The stock mouse does not have grip there, and the thumb buttons endure constant sideways force as you lift the mouse during daily use, so it's a terrible place to put tape, as it will come right off.My mouse now looks absolutely fantastic and is so easy to lift compared to before with my worn grip.If I have any issues with peeling later, I'll come back and edit this review. So far so good!

The replacement grip tape comes on a 3M pad, just like the Razer official tape that comes with newer mice, plus a handy alcohol wipe to really clean the surface. Applies simply and fits snuggly, thickness aligns with the raised middle surface. 5/5 this is what you want for your Razer Viper Ultimate, just make sure you peel off the original grip and scratch off the the thin layer of foam beneath, down to the plastic.

Reccomend using a flat head screw driver to get the thick plastic removed from original skin. But the grip feels so much better! Perfect fit!