Milescraft 1500 DustCutter - Contractor Saw Dust Collection System , Black

Works great! Loved that I didn't have to drill any holes or worry about attaching snaps. The other bag we bought didn't fit right. This one is awesome, no more mess and the pluggable hole in the bottom hooks up to my dust collector easily as well.

Product would work if it wasn’t bigger than most contractor saws. If you upgrade saws you’ll have to find replacement Velcro which I’m having a hard time finding

Got this to put on my jobsite table saw to cut down on the dust when I'm cutting inside the garage. Fits perfectly with included VELCRO tape. Convenient port on the bottom can easily plugged with included foam plug, or attached to shop vacuum or connected to dust collection system with hose adapter (not included).

A nice addition to any table saw to help manage the saw dust - if you don't already have a vacuum system. I really appreciate the comments by the other buyers and their recommendations about enhancing the attachment and functionality of the Dust Cutter. Works as advertised!

Overall this is a well made, useful product and despite its limitations, I'd buy it again. To make the most of it, I made several modifications. Because this is a "one-size-fits-all" I decided to customize the fit to my saw. I measured and pinched the four corners and riveted them so as to obtain the exact dimensions I needed (see photo). I also decided that rather than my shop vac, I wanted to attach my 4" dust collection system. I removed the original connector (simply slides off) and replaced it with an adapter (see photo). Because the adapter was not tight enough to stay on by friction I added some short screws. In regards to saw attachment, I listened to others who complained about the velcro system as being inadequate. It's pretty apparent that with dirt, vibration, the temperature variations in my shop and the pull of a vacuum hose that relying on the taped velcro would be foolish. I followed the suggestion of others and used magnets (see photo). Upon initial power-up of my vacuum I discovered another issue. Despite the cage used at the vacuum connection, the surrounding material was sucked against the cage limiting flow. To overcome this I used an old plastic microwave dinner plate that I modified and screwed to the cage's flange. worked perfectly. Finally, I'd advise against the use of the magnets. While they adequately held the cloth it was a real pain to install and also resulted in some gaps. I ended up tossing the magnets. As suggested by others, a more permanent attachment made sense. I riveted one side and then for the remaining three sides used nuts and bolts. Some have suggested rivets all around. Bad idea. In order to keep the saw in good condition, the jack screws for elevation and bevel need to be periodically cleaned and they, along with the support bearings, need to be lubricated. In summary, a good product that can be made great with some work.

With a little adaptation I added this to my old saw that had its original base. It does catch a lot of dust that otherwise would have floated around my garage. I have had it about 6 years now and it has held up well.

Used as prescibed on the bottom of my saw

Update the bag just continues to fall off. I will likely end up drilling holes and riveting to my base. I have no idea why this company doesn’t have magnets they work extremely well. Went from 4 to 1 starSo I’ve had this for about three days now. I had a project where I was ripping a bunch of pressure treated lumber. This product is great but no product even the expensive two stage vacuums with HEPA filters get all dust. I would say the company is honest with a vacuum or shop vac connected to this bag you probably do achieve 90% dust collection.I see zero issue with the Velcro adhesion to the bottom of the table saw. In other reviews people seem to be complaining about it. As long as you use some type of degreaser and clean the surface that you’re sticking the Velcro to you’ll be just fine. That said do I think that magnets would probably work better? Yes, they absolutely would. It’s great that they provide a plug to you so if you decide to just rip a few or cross cut a few pieces of wood you don’t have to go through all the trouble of connecting a vacuum.I will say for what it is it’s a little expensive. Still Its a nice addition to any table saw. My one tip is to make sure that you’re cleaning the dust out fairly frequently if you’re not using a vacuum. I’ve already dropped my arbor not once into a bag of sawdust and it wasn’t extremely easy to fine luckily I had a magnet.What I recommend this to a friend? I’d probably tell them about it give them the good and the bad and let them make the decision. I’m not over the moon about it.I hope this was helpful.