Nilight 90013L 12PCS Round Toggle LED Switch 12V Car Truck Rocker On-Off Control Blue Green Yellow Red

These switches are EXCELLENT! They are constructed with high-strength plastics and mechanically they are VERY solid. I don't see how they could wear out even if used hundreds of times a day for decades.There are three connectors on the back that are mounted solid - basically an extension of the whole switch. Nothing loose back there at all. One of the connectors is gold-ish in color and must be connected to ground so that the LED lights up when the switch is turned on.For those interested in the tolerance specs, I decided to sacrifice one of these to see just how many volts the LED would tolerate and was pleasantly surprised with the results.First of all, these are rated at 20 amps. HOWEVER, I would NOT run 20 amps through these at 12 volts. That's 240 watts and if you can imagine the kind of heat you might get from 240 watt light bulb - you wouldn't get that kind of heat concentrated in this switch, but from the looks of everything, I believe the switch would most definitely get warm if not hot at that kind of amperage. And of course, if the switch needs to sustain 20 amps at 12 volts, then you should be looking at a 25 amp rated switch AT A MINIMUM, so I would say it would be safe to use this switch at 10 amps but not more than 15 - TO BE SAFE!SO, in my testing, using a bench power supply, the LED starts turning on at around 2.5 volts and starts getting close to max brightness at around 5 volts, though it does get about 15% brighter between 5 and 12 volts and it gets no brighter above 12 volts.As I continued to increase the voltage, the LED didn't flinch until I got past 45 volts, and at 50 volts, I fried the current limiting resistor attached to the LED. I had my bench power supply set to max amperage at 5 amps, yet this LED hung in there to where the resistor fried before the LED ever got hot enough to burn out. In the photo, the LED is sticking up but it was folded over, laying on its side next to the resistor. I moved it to get a good photo of the burnt resistor.I would say that as long as you keep your wattage under 200 watts, you could use this switch at any voltage up to whatever voltage calculated out to be 200 watts (take the voltage times the current to calculate wattage).After I fried it, I took some pictures so you can see what's inside these things. Very basic ... one LED and one current limiting resistor and a design that is top-notch with a very solid build. These things are NOT waterproof so I would not use them in any application where they might get wet, but they would be perfectly fine in any application where they are only exposed to open air (or in a vacuum I suppose). They have a solid click feel to them and they look very professional.I haven't measured around the inside of the ring yet, but if the hole was drilled to the right size and the material you're mounting them to isn't too thick, they will push in and click tight against the mounting plane and they will hold that position very well.My only complaint about the company is that they included an insert with a QR code that said to scan it for a surprise, free gift. When I scanned it, it took me to the warranty registration page on their website. Once I registered it (and provided a screenshot of the order details along with a photo of the UPC code on the package, plus my name, email address, and phone number), I was not offered any gift at all.I certainly understand that companies want feedback from their customers and warranty registration is a good thing for a manufacturer, but manipulating people into registering their product by promising them something and not delivering on that promise is just bad ethics. Don't offer a gift if you don't intend on giving one and let people decide for themselves if they want to register the product warranty or not without manipulating them with a lie in order to get them to do it.Overall - for this price, these are amazing switches. I highly recommend them and will purchase these again if I ever need any.

Works well

GOOD FIT, A 3/4 INCH STEP DRILL GETS YOU CLOSE TO THE RIGHT SIZED HOLE, AND A LITTLE MORE SANDING/GRINDING GETS YOU TO THE .77 INCH MARK THAT YOU NEED. AFTER THAT, YOU WILL NEED TO CUT/SAND/GRIND A SMALL REGISTRATION MARK IN THE MATERIAL FOR THE SIDE NOTCH ON THE SWITCH, SO THAT IT WON'T SPIN AROUND ON YOU OVER TIME.All 3 of my amber LEDS were wired backwards, with two prongs being live and one neutral, so it delivers power but only lights up in the off position (good for a standby indicator situation I guess). The green, blue and red ones seem to be wired correctly, but I've blown a few of the red switches (the resistor inside, not the LED itself) while plugging my device in while the power switch is on, and I can't really change out the 1K resistor inside the switch because it will affect the current being delivered. I just have to make sure the device is in the off position before plugging it in. They are however, fairly easy to get into after prying the caps off at either side by the hinges, then you can re-solder a fresh resistor and re-loop the wires around the plastic button frame if you're inclined to do so.I'm not sure why they went with actual colored LEDs inside of the shell, when the plastic window that the light shines through is also colored. The double layer of color makes it a bit dimmer when they could've used white LEDs inside and they would be a bit more visible, also the 1k resistor inside is a bit much and dims it further. A 330 Ohm resistor and white LEDs would probably be a better fit. I may start experimenting with the insides and see if I can optimize them.

You can use the toggle only or with surround. I had enough space on my Ryobi snow shovel to use the surround. I know. I bypassed the safety. Well what was a danger was trying to work with the crummy safety trigger.. The click, click, click and still nothing is replaced with a on-off that works as it should.I removed my trigger and safety slide then wrapped the handle with a 1 inch wide long length of stretch velcro. It provides no slip handle control while my tool is TURNED ON and in use.

I mounted this switch to the inside of a hatch in my duck boat. Installation was a breeze. One of the most impressive features is its weather resistance. I appreciate how it stands strong against moisture and unexpected splashes, which is a common occurrence when you're dealing with wet gear and equipment. It still operates flawlessly even after a few unfortunate drenching episodes. The LED indicator light is bright and ensures you know where the switch is. A handy feature when you’re loading up the boat before dawn.

Nilight Round Rocker Switches:These worked well for my project and they seem to be well built.The switch and nut threads mesh properly and tightens switch in place securely.This is the first time I have used them so I can't testify to there longevity.

these installed in my current project car. i like to use a lighted switch for a quick reference for the fuel pump and oil accumulator. i can shut these off while working on other systems and turn back on for normal operations.these install nicely with a 7/8" hole and the multiple colors are a bonus

I received the switches and two of them don’t work at all!! I love the look of them. Just not pleased about two not working