Pyle4" Car Sound Speaker (Pair) - Upgraded Blue Poly Injection Cone 2-Way 180 Watt Peak w/ Non-fatiguing Butyl Rubber Surround 110 - 20Khz Frequency Response 4 Ohm & 3/4" ASV Voice Coil - PL42BL

For the $$, can’t beat these. Sounds surprisingly good at this price point - paired them with an older Alpine unit from a car I’ve since sold about 8yrs ago…I spend a lot of time in my dump truck, so well worth the time and $$.Highly recommend!

Good Product at good price.

Satisfait

They kick ass. I'm a life long firm believer in pioneer bang for the buck, but these pyles are impressive. So far. I don't have them on an amplifier yet, just on the line level, that's why I said "so far" I have the 6×9 pyles in the back and 6" matching pyles in the front doors. I have a pioneer deh 160bt head unit, the four pyles and a 15" Rockville sub in a bass tube that I made from a 16" concrete sono tube. With all the adjustments that the pioneer head unit has, it really hits hard and believe it or not, even without an amplifier on the pyles,the highs are super clear. What I do is turn the remote bass knob down and then turn the head unit up until the point just before distortion and then you do the same for the remote bass knob. I'm going to paint the bass tube when I'm done with the bodywork and I'll paint it with the rest of the car, so don't laugh

They come at a pair so you get 2 instead of just one speaker im ngl i thought it was just one but both of them came. I recommend you to get a frame with these just so they can fit better because i used these for my nissan altima 2013 and they required a frame. They might also require a speaker harness due to them not being factory made. Sound wise they actual sound very good i personally feel like they reduce the bass tho, but for the price they are at i 100% recommend.

I bought the Pyle PL53BL speakers to replace the factory rear seat side panel speakers in my 97 Dodge 2500 Club Cab. I bought these before removing the original speakers, as all the speaker fitment guides here and elsewhere indicated these were a fit. They did fit but weren't an exact fit as the original speakers were closer to a 5.75" or possibly 6" size. The two speaker mounting points in the truck's metal were spaced just close enough to enable me to get mounting screws in the slots in the Pyle speaker frames, so they did mount OK. However, due to the smaller diameter there was a sizable air gap (about 1.8" or so) between the speaker and hole in the truck's metal. I closed off this gap using some putty-like weather rope seal from a big box home improvement store.I'm running these speakers on an older Alpine CDA-9856 head unit and Alpine 3566 6-channel amp (conservatively rated 35W RMS x4 and 120W RMS for bridged sub channel into 4 Ohms). Following advice from several reviewers and professional installers, I bought a roll of sound dampening material to apply to the door panels and elsewhere. I bought roof repair material - Tape and Seal is one brand - which is very similar to another very high priced product and it worked quite well. Once this was done and the speakers were mounted and connected to the amp, I turned it on for the first time. After the initial checkup to make sure all speakers were working, I cranked up the volume to a pleasantly loud level and was very surprised and pleased to hear the quality of sound coming from these inexpensive speakers. Being 5.25" bass drivers they understandably don't produce much bass output but the midrange and highs are much smoother and detailed than I was expecting. I paired these up with a pair of Pyle Driver PLDV6K 6.5" 2-way component speakers in the front doors and I'm very pleased with how nicely these compliment them. They're well matched regarding their efficiency, producing very near the same volume level and similar sound quality. While not quite as smooth and clear as the fronts, they do a splendid job of providing clean sounding music to fill the rear seat area and filling the back of the cab. They're SO much better than the original factory speakers.So, long story short, I HIGHLY recommend these for anyone looking for a very reasonably priced, smaller coax system and wants surprisingly accurate, smooth and detailed sound quality and listens to their music at reasonably loud levels. I would definitely buy these again and recommend these to others.UPDATE: After about 2 years these speakers have basically "given up the ghost" and for the most part are now inoperable. I had hoped they would be able to handle the clean power of my Alpine amp, especially since they weren't getting all the bass signal they would in a full range system, but alas they didn't. They are now working intermittently, with audio "popping on and off" as the speakers' litz wire (the flexible wire between the frame and cone) apparently makes and breaks continuity. I still liked the sound quality they produced when they worked well earlier, I'm just now believing they aren't made to handle even the 35+ watts RMS/channel my amp can produce. The front Pyle Driver PLDV6K 6.5" 2-way component speakers on the other hand are still performing well, which is why I believe it's just a simple matter of inadequate power handling ability that has caused these speakers to die off. In a lesser powered system they may work better and longer.

Great little speaker! I have built these into small enclosures to when added blue tooth to antique radios. The sound good and have excellent frequency range from low to high. They are well made with good fit and finish.

Just got these installed in my truck and they sound pretty good…The wiring that comes with them is very substandard IMO, It’s way to thin/ flimsy!! When hooking them up, one of the wires broke during the process!?! If I’d had more time, I would’ve used “actual thicker speaker wire!”