Beartooth StockGuard 2.0 | Neoprene | Slip-On | Prevents Gunstock Damage | Made in USA

I was looking for something to take the edge off of the recoil impulse on a mossberg 930 shotgun; 100 rounds of trapshooting and the light hollow synthetic stock did not make for the most comfortable experience. As the gun fit was good for me and I shoot it well, I did not want to alter the setup too much. After some researching of the various stock/comb pads available that were thin enough for my application, I decided to go with the StockGuard 2.0. As it arrived just before I was going to the range, I got to give it a try immediately. Perfect! Just enough padding to soften the recoil that was formerly whacking me in my cheekbone every shot, and thin enough that the ergonomics of the gun fit were basically the same. As an added bonus, my highly figured plastic stock is also protected from scratches and nicks heh heh.The StockGuard 2.0 itself is very well made, fits great, and goes on the stock very easy, but also stays fixed where you put it once it is on. Beartooth got this shipped out to me very quickly too, that was a pleasant surprise. All in all, I'm very pleased with both the product and the service. Buy with confidence!

Put this on a rifle that came with a Hogue stock. Stock is terribly uncomfortable to shoot with a high powered rifle (rubber grips your cheek) but this makes it usable. Very high quality and the pattern is perfect.

Perfect fit.

I have four of these. Two of them are on shotguns two of them are on rifles. I have to say that I honestly purchased them mostly to put a foam insert under to raise the cheek well for an optic. I know you can purchase them with the foam insert however I saw on YouTube someone who bought different foam inserts that come in 3 sizes and I went that route instead. The only one without the foam insert is on my shotgun I use for trap and the only reason I have that is because I ordered a Mossy Oak and they sent me a Realtree Max 5 by accident so I kept it seeing as my trap gun is colored in mossy oak shadow grass blades. It does actually work out to reduce slightly the cheek slap you get from shooting repeated rounds. It is a very decent product. They are a little stiff and fumbly to install but it is decent quality for what I have found so far they have held up. They do tend to move around a little bit on a composite stock. Not a lot but it's not completely snug so you do have a little adjusting if you shoot a lot. Overall I think it's a very worthy purchase and a quality product.

Relatives and myself have been using these for some time. The main reason is to keep wood-stock guns with sensitive clear finishes from scratching during hard hunts. Though i will say, don't rely on these to keep your gun entire scratch free, as i was surprised to see dings after the season when removing. But thats no hit to the product, just the reality of the matter.These can be a bit of a pain to install, just because of the super grippy inside material. Once applied, they stay in their position. I can't comment on the loops, as the model i have is the no-loop plain black cover. But relatives haven't complained of their covers when holding standard hunting cartridges.An area for improvement for this product would be water-proofing. These will soak up water on really wet hunts. Would be nice for a full waterproof model. For relatively minor damp conditions they do a good job of staying dry.I recommend removing after season on wood stock guns to prevent locking in any moisture and potentially affecting the stock.

Fits stock well. Great product. +++++

I am using this stock guard on a Marlin 336 lever action 30-30. It was a bit of a chore to get on there, which I think was great for this type of item. The inside of the sleeve is very tacky rubber, and really needs to be coaxed along the wood. In the long run, this is going to mean serious stability and a repeatable cheek weld on the firearm. It also means I don't have to worry about my extra shells sliding over to the bottom of the stock or becoming hard to locate.The color was a very close match for the dark brown leather mossy oak sling, and the stitched window in the sleeve for the sling mount means this shouldn't become a point of undue wear, or disintegration for the product.Overall, this is a well thought out product that works well for my application, and the quality of the neoprene, edging and all stitching seems very good.

I purchased this for my Marlin 336rc. It fits well on the weapon. It was a bear to put on but I can say that I see the potential to loose cartridges because it is a little loose for the 30-30 cal. It does hold a 270 or a 7mm cartridge quite well though.