交付 Malaysia

获得最佳体验获取应用程序

下载应用程序

我们从

阿联酋
英国
印度
美国
日本
KOREA

客户服务

关于我们

客户支持

daier24V 6S 40A 18650 Li-ion Lipolymer battery BMS PCB Balance for ebike ebicycle

Q: is there a specific order that wires need to be soldered to the board? Mains first then balanced leads for example?

Assuming the wires are not connected to anything on the other end (aka your battery holder is empty and you have no load or charger connected ) you should be fine with any order. I would recommend moving from one side of the board to the other so you don't concentrate too much heat in one place. Try not to unsolder the pads from the board by applying to much heat. Don't solder live wires!

Q: Where does the charging lead connect?

Not answering the question, but my BMS had the same issue! No voltage/current at P+/P- when everything else is wired up!

Q: can anyone tell me how to connect to the load? do I use p+ and p-?

Initially it was not clear to me where the charge and where the load connected. Other reviews clarified that the both the charger and the load connect to the P+ and P-. The BMS auto switches between input and output depending on the voltage on P+P-. I tested it on my Power wheels car and the full 20 plus volts were on the (P+P=) output terminals. With the charger connected for couple hours it raised the voltage from 3.6 to 3.8. One cell was at 4.0v . I will leave it on the charger overnight and see if it balances better. If you connect your load to B+B= , it will work but you will not have any load overcurrent or under voltage protection for your battery pack. You would be able to run your device till the battery is totally dead, which damages l-ion cells.

Q: Can I wire two of these in series to make a 12s?

Yes, you probably could, but just be aware of the fact that if the BMS is unhappy with the 18650's that you have attached, it will shut down, so you're adding more points of failure by wiring two in series. I actually struggled with this 6S BMS for a while, and nearly gave up on it, because it kept shutting down, until I realized that the resistance of some of my cells was too high. After re-grading all my cells and culling the highest resistance cells, the BMS was able to stay up.

4.0/5

产品编号: 388596675

安全交易

细节

Brand
daier
Battery Cell Composition
Lithium Ion
Recommended Uses For Product
Bicycle
Unit Count
1.0 Count
Voltage
24 Volts

经常一起购买

daier 24V 6S 40A 18650 Li-ion Lipolymer Battery BMS PCB Balance for ebike ebicycle

200mm(7.9in) Width PVC Heat Shrink Wrap Tube 18650 21700 26650 Lithium Battery DIY Battery Pack 3M(9.9ft) Length Blue

MatchWhiz Flat Width 5.9in(150mm) PVC Heat Shrink Wrap Tube for 18650 21700 Lithium Battery DIY Battery Packs Blue Length 9.9ft (3m)

描述

daier24V 6S 40A 18650 Li-ion Lipolymer battery BMS PCB Balance for ebike ebicycle

有问题吗？看看别人问了什么

is there a specific order that wires need to be soldered to the board? Mains first then balanced leads for example?

Where does the charging lead connect?

can anyone tell me how to connect to the load? do I use p+ and p-?

Can I wire two of these in series to make a 12s?

常见问题

TrustPilot

TrustScore 4.5 | 7,300多个评论

阿里·H.

发货快，包装精良。Leatherman 工具手感非常高档和坚固。

1天前

Sneha T.

我收到的产品完好无损。总体来说服务很棒。

1 个月前

查看所有TrustPiLot评论

全球购物，通过 Desertcart 享受优惠

物有所值

各种产品的价格具有竞争力

全球购物

为 100 多个国家的数百万购物者提供服务

增强保护

深受全球购物者喜爱的值得信赖的支付方式

客户保证

深受全球购物者喜爱的值得信赖的支付方式。

沙漠车应用程序

随时随地随时随地购物。

RM142

关税和税费包括

Malaysia店铺

免运费

with PRO Membership

免费退货

30天对于 PRO 会员用户

15天无会员资格

安全交易

TrustPilot

TrustScore 4.5 | 7,300多个评论

伊姆兰 F.

非常可靠的商店，产品真实可靠。一定会再次购买！

2 周前

Farhan Q.

交货时间非常好，包装也很安全。

2 个月前

查看所有TrustPiLot评论