Lee Precision 90058 Perfect Powder Measurer (Red)

Q: What are your experiences with consistency between each charge with this measure?

Opinion, it is good enough for staying within the published load if you target the center, but if you want tenth of a grain precision at rifle weights, or want to max out the load, you will need additional trickler. Some real data, using VIHTAVUORI - N133, sample count=10 at each volume setting (reloading some .223, getting my reliability data and picking a volume for target weight) at 1.00 CC average was 12.95 grains, min weight was 12.8. max was 13.0 at 1.50 CC average was 19.54 grains, min weight was 19.4. max was 19.8 at 2.00 CC average was 26.14 grains, min weight was 25.9, max was 26.3 at 3.00 CC average was 39.09 grains, min weight was , 38.7 max was 39.4 On the worst case, 3 standard deviations was 2.6%, the rest 1.5%. 3 standard deviations about 99.7% of your production falls within this range. So if your in the middle of the specified range... more example say the spec is 22.1 to 24.5 grains, you go with 23.3 as your target and use the 2.6%, 99.7% of your production would fall between 22.7 and 23.9 grains. This is well within tolerances. However if you are trying to make high precision ammo 2.6% of target as 3 standard deviations is unsuitable and you should invest in a powder trickler to precisely top off a volumetric measure using this tool. If this is too mathematical, find an engineer or a math geek and show it to them. They will tell you I made unproven assumptions, but in general I am correct. 99.7% is assuming bell curve and perhaps I should have gotten more data at each setting. Data will vary with the specific powder used and the person using the tool, but this is probably typical results. Keep the powder reserve full. Be consistent with your motion and careful with your pan. Oh, plotting all the points on a graph of volume to mass made a pretty good best fit straight line, so it is fairly consistent.

Q: Will this measure dump directly into a piece of brass without spillage or will I have to dump the powder into a tray & then dump that into the brass?

you can do ether way. i have dispense directly into 223 brass, no problem

Q: Does this come with a stand? Or do I have to buy the stand separately??

Comes with the little stand that’s pictured.

4.4/5

产品编号: 759918924

安全交易

经常一起购买

Lee Precision 90058 Perfect Powder Measurer (Red)

Lee Precision Auto Prime Shell Holders

Lee Precision Modern Reloading 2nd Edition New Format

描述

有问题吗？看看别人问了什么

What are your experiences with consistency between each charge with this measure?

Will this measure dump directly into a piece of brass without spillage or will I have to dump the powder into a tray & then dump that into the brass?

Does this come with a stand? Or do I have to buy the stand separately??

ENVIA PARA O BRASIL? CEP 22720410 / SHIP TO BRAZIL? ZIP COD 22720410

常见问题

TrustPilot

TrustScore 4.5 | 7,300多个评论

全球购物，通过 Desertcart 享受优惠

物有所值

各种产品的价格具有竞争力

全球购物

为 100 多个国家的数百万购物者提供服务

增强保护

深受全球购物者喜爱的值得信赖的支付方式

客户保证

深受全球购物者喜爱的值得信赖的支付方式。

沙漠车应用程序

随时随地随时随地购物。

TrustPilot

TrustScore 4.5 | 7,300多个评论