Zalmani4 Airflow Gaming PC Case - ATX, Micro ATX, Mini ITX Computer Case - 6 x 120mm Quiet Fans Pre-Installed - Full Mesh Design - 360mm Radiator Support, White

You get a lot for your money with this case, it will accept a standard ATX board and the layout is well tought out. I managed to fit a 280mm Aio for the CPU, a 240mm rad with pump/reservoir combo to cool a 2080ti card fitted with a waterblock in vertical position. The size of it is pretty small, since my goal was to build an affordable living room PC with leftover parts from my upgraded main build. I'm very pleased with the results. I recommend it.

It should be more than enough to fit a RX 6800 XT inside but it didn’t. The extra standoff also weren’t couldn’t fit into the case properly.

Excellent bang for your buck, definitely recommend upgrading fans eventually if you do get this case. Also the vertical mount is very small and does not fit most riser cables. But other than those it has great airflow and room.

Awesome case for the price its a steal 6fans and more accessories in a bag for 100$ cant beat it its amazing

When I received my package, both the outer Amazon package, and the inner Zalman box were opened. At least the outer box was already opened prior to UPS delivering it.Despite the claim of C. Church (Vine Voice, which I cannot join as an Amazon Employee despite having received an invitation), there is NO fan controller. It is not mentioned on this site or in the case's documentation.This is a budget mesh case and you can tell, although they did a very good job of making sure there are no sharp edges. For anyone who wants to save money and doesn't need a LARGE case, this is a good option, unless you absolutely MUST have a USB-C 3.2 on the front I/O. You could modify it by replacing the 2.0 with 3.2C, although it's a tight squeeze.PROS:Exterior: Black The left side and front are mesh, with a magnetic mesh filter. There is also a large mesh section on top that has a magnetic mesh filter on the outside. The PSU air intake has slide-in piece of mesh filter. The front mesh panel is made of metal mesh over a plastic piece on each end. 7 card slots + 2 vertical card slots Slot covers are attached with thumb screws (i.e. reusable) and it comes with an extra cover Aside from the front, everything is metal. 4 5/8" plastic feet with rubber bottoms No LEDsGraphics Card (GC) support: Adjustable GC anti-sag support Vertical GC mount brace Max. GC length 320mmStorage: If you remove both GC supports, you can mount 2 3.5" storage devices (hardware not included) 2 2.5" SATA drives can be mounted on the back of the mobo plate with included frames and thumb screws There is a double 3.5" drive bay in the PSU area that can be slide forward and back by loosening 4 thumb screws on the bottom of the case. This makes it much easier to adjust than other cases where the screws are inside, and only offer 2-3 positions. The removable plates for the drives are of plastic.Includes 6 120mm fans. The 3 front fans are mounted on a very large-bore honeycomb panel that isn't removable unless you drill out the rivets. The front can accept 3 120mm fans or 2 140mm fans or possibly 2 140s and a 120. There are two top fans are mounted on a permanent large honeycomb panel. The top can accept up to 3 120mm or 2 140mm fans. The rear can accept 1 120mm or 1 140mm fan. The fans are daisy-chained together using 3-pin standard DC connectors, so you'll only need one fan header on your mobo.PSU area: The PSU shroud has large honeycomb holes ventilating the PSU area. There is an opening on the side of the shroud so that the PSU is visible from the left side. Useful if you have a PSU with LEDs there.Misc:The top I/O panel has microphone & speakers jacks, 2 USB 3.0A jacks, 1 USB 2.0A jack, power, reset and an LED button, the cable of which goes to the motherboard LED jumpers.Standard cables for connection to the mobo are included.The motherboard area has a large opening for easy access to the rear mounting hardware of the CPU.The accessories bag includes bolts, zip ties, a system speaker on a cable, and standoffs.CONS:Fans: The fans are low quality, max 1,000 RPM, don't move a lot of air or provide much pressure at all. You'll probably need to replace them if you have problems with overheating. The fans will not be able to handle the barrier of the filters properly. Even the rear fan struggles to move much air at 42.8 CFM through the holes of the cover.The front filter does NOT cover the entirety of the front mesh; the 45-degree corners and sides are unprotected.The mesh is made with smaller holes that don't necessarily line up with the holes in the panels.The 3.5" drive plates for the PSU bays are plastic, warped and don't fit well.No cable management system.No LEDs