Partsam2Pcs Double Led Trailer Tail Lights with Horizontal Mount Dual Stop Turn Tail Backup Reverse Lights 33 LED, Surface Mount RV Double Led Taillights, RV Double Led Tail Lights, Black Base

I have learned in the installation. That if you have not had LEDs on your RV, there are a few things that NEED to be addressed. 1. Fast blinking is very possible in RV's under 1999. If using these rear lights. You should also replace the 2 front blinker bulbs with LEDs that work for your vehicle. Then buy an Adjustable LED blinker switch that works with your vehicle. Then replace the old switch with the new Adjustable switch. Put another one of your vehicles in front of the one you are adjusting. Turn on the blinker of the other vehicle. Then turn the knob on the adjustable switch until they match as best as possible. It is so much easier than having to install resistors in the circuit of the blinking lights. The resistors do heat up if used for too long a time. If you have a wooden underlayment as do most older RV's. This could become a FIRE HAZARD. Plus the ADJUSTABLE switch was so much easier and cheaper to do. No Mechanic is needed. Plus this installation was so much SAFER. Now I have very visible lighting that everyone can see.Thank you for making this lighting kit. It fits perfectly where my originals were. Right down to the screw holes.Well a few months later and finding out I had NO CRUISE CONTROL. I had to install resistors in a safe place that would resist heat the best. Now I have my Cruise Control back and no back lighting when the engine runs. The lights work as they should and so does my cruise control. See the pictures. The resistors stay much cooler in the are I installed them in. They are way up under the rear deck bottom of the storage and the shower. They are Formula J87 make 50W 6 Ohm. By Automotive Lighting.

These lights were a perfect fit for the early 2000s vintage lights on my Arctic Fox 990. Wiring them up was straight forward. Only detail to keep in mind is that they have 2 ground wired instead of the 1 the older lights have. No big deal. Just connect both white wires with the single ground on your rig.Screw holes lined up perfectly and I needed only a screw driver for install.They are much brighter than the old incandescent lights they are replacing. The old ones were so dim I worried about others seeing my brake lights during the day. These will be much safer.They're pretty cheap and made in china so we'll see how long they last. I will update this review if I have any issues.

These were a great drop in replacement for old lights that had corroded. The size is identical to what was in the RV before. They are significantly brighter than the original equipment.My only complaint is that since they replaced older incandescent lights they don't work properly with the flasher and blink quickly when the turn signal is used.

These were exact fit. The new ones were led, the old ones had regular bulbs. The new lenses are thinner which I really like. They are well built and shine bright on brake and backup, yet just right for tail. And they look awesome. Plus they were about 1/4 of the cost compared to original lights.

The original 2007 Winnebago tail light assembly was aging and the seals were cracking and a lot of condensation forming on the inside. Not to mention the older incandescent bulbs which were giving me trouble with poor connections and having to constantly clean them with emery cloth and dielectric grease. I also never liked the way the originals stick out over 2.5 inches from the body.The original fittings were 9 X 9 inches and these new LED Partsam lights were the closest in size I could find (9 x 7). This meant 2 of the mounting holes from the original lights would be covered but two would be exposed. Filled the old exposed holes with silicone and then used a push in plastic plug so not a perfect install but I'm more concerned that those behind me can see my lights, breaks and my indications to turn.Wiring was very simple and my rig is built on a Cheve Express chassis with a solid state flasher unit that supports LED indicators so all works great.I have only tested in the day light and can see these are at least twice as bright as the old. Very happy!Lights do come with a large black foam gasket but I also added a bead of silicone around both sides and the top to ensure no moisture gets in. Recommended!! Hopefully they will continue to shine bright for many years to come.

The replacement of these lights took about 15 minutes each. Perfect fit. Even all of the screw holes lined up. The durable gasket that comes with each light caused me to not have to use butyl tape. I do not like using butyl tape. Great product. Good price, too.

I put these on my 1992 enclosed car trailer to replace the incandescent light bulbs. These units are amazingly bright. I can see the ground light up 10 to 15 ft behind the trailer when using the brakes or turn signals. Reverse lights are a plus as well extremely bright. Very happy would buy again

I put this on a 20 year old camper and it is a great improvement. Easy to install and wire up.

Direct fit on 89 motor home, easy installation, nice an bright ,priced reasonably very satisfied

Great replacements on my 1986 motorhomeVery bright and bolted in original spacesHighly recommend

They fit perfect and work the way they should do perfect.

Easy to install work great

Very good price and value