LCD Display Touch Screen Digitizer Assembly Repair Replacement for Samsung Galaxy Tab S7 SM-T870 SM-T875 (Not for TAB S7 Plus)

I read some of the other reviews before I ordered. Most were good to great experiences with this item. I didn't want to purchase a new tablet. A new one would have been $350+ used. The replacement display was bubble wrapped and came with all the tools needed to replace, including the adhesive stripps to secure the screen. The replacement works great, and display works and looks like the original. WATCH A VIDEO ON HOW TO REPLACE. Be careful....The display is glass. The only problem I had was that the adhesive isn't as strong as I would like it to be. But that could be a good thing, if you didn't connect something right and you need to remove it again. Now that everything works fine, I'm going to use a heat gun or blow dryer to heat the edges up, when the adhesive cools down, it should stick better. Heating the edges can also help removing the screen. **there are 3 round transparent areas around the display glass. 1 for the camera, 1 for a dimming sensor by the camera, and 1 for the display dimming sensor on 1 side. They are only transparent areas. The camera and the sensors are not attached. When the display is removed, you can see the 2 small copper colored square sensors and the black, round camera inside of the outer edge of the tablet. DO NOT COVER THOSE WITH THE ADHESIVE STRIPPS. Also, the transparent areas of the replacement may be covered with tape. Remove those. You can see the transparent areas in the glass, when you hold it up to the light. Be careful with the tabs on the ribbon cable connectors. They are kind of fragile. Like I said, watch a video on replacement. Bottom line..... great product, be patient, be careful with broken glass.

Works well and looks good. Removing the old, shattered screen without it shattering even more was hard. A lot of care was required to ensure glass shards were cleaned up out of the tablet and to remove all the old adhesive. The install was easy and straightforward. This screen does require the reuse of ribbon cables and a small part stuck to the back of the screen. Therefore, care should be taken when removing the old screen so the cables and small circuit card attached to the screen are not damaged. The tools included are a mixed bag. Screw drivers are not required for screen replacement. The pry tool is not great. I used a few stronger metal pry tools I had on hand. The adhesive tape works well, and the tweezers were an absolute must for glass shards removal and adhesive work. I have not tested the s pen.

Since I am using my tablet to write this review, it worked! It took me 4 sessions to complete, but being a chiropractor this was a pretty fast install. I first had problems breaking the seal. I used a heating pad set to medium for about 20-25 minutes. The plastic spunges don't work well. I was able to insert a small but sharp pen knife. That worked to break the seal. Then I used the mmobiel metal opening tool (Amazon) to insert and slide around the perimeter. You need to continually warm the adhesive to release ( hairdryer). The screen came off fairly easily. I watch numerous YouTube videos, some better than others, utilizing the opening tool. Following the video step by step, removing adhesives, removing and reengaging the 3 connections, using new adhesive strips everything came together. Before closing the 2 pieces, I tried turning the tablet on. NOTHING. No power, no lights. I took a break, plugged a power supply in then turned it on. It powered up. I sealed everything up, took off the plastic covering and, now I am using my tablet. Do not place adhesive over the camera or proximity sensor. The pen works as well. TAKE YOUR TIME. WALK AWAY AND COME BACK. It is not hard (I had removed a screen before to get to a battery in another device). This replacement cost about $50. U break I fix wanted $150, and a new samsung tablet was $400+. Not hard, but tedious. Work slowly and take breaks. It helps with frustration. Good luck PS- it's still working after writing the review

Works perfectly. Comes with adhesive but would recommend professional tape. Be very careful with removing the old screen as you must keep the Wacom chip and cable intact to transfer to the new screen. I have the Keyboard case and Samsung S Pen for my Galaxy Tab S7 11 inch. The S Pen works perfectly with this screen. I tried two others prior to this from other sources that did not work with the S Pen. Provided all the stock is the same for this product, this is a perfect replacement. As a side note, be sure to remove the protective plastic over the camera and sensor holes before final installation. As well as the pill tab at the end. Always test BEFORE final adhesion to the device! Use a heat gun on the edges after screen has been attached to really seal the contact. Good luck 😊 Update: Screen has a light bar of discoloration through horizontal center of screen. Not noticeable on bright backgrounds but definitely on darker apps and videos. Screen developed a crack from one corner to the other. Very fragile glass. Was never dropped, compressed or damaged in any way. Just one day it had a crack through it. Would recommend trying to find an OEM screen if possible.

Received the screen with no apparent damage. Upon connecting to the tablet and testing, before gluing down, found a dead zone for the s-pen. The issue stretched the width of the screen and about 1/4 inch tall. Image was good and touch functionality was as expected. Requested a replacement and after waiting for another shipment the second worked fine and my daughter is back in business. I ordered the B-7000 glue as recommended in install videos instead of relying on the little tape strips provided.

Perfect for repairs!

I damaged the display while replacing the USB charging port. I thought about just replacing the tablet but decided to gamble and swap out the display. I'm glad that I did. The shipping was amazingly quick and it was on my doorstep before I was even awake the next day. It was incredibly well packaged in a thick cardboard box with several layers of bubble wrap used. All of the tools required to do the job are included with the exception of a heat source to soften the adhesive. I just warmed up my oven and then left the tablet in it for 30 minutes. Disassembly was easy using the included tool kit. I've got bad eyesight and shaky hands and it was still okay. MAKE SURE TO DISCONNECT THE BATTERY FIRST AND RECONNECT IT LAST. The new display is 100% perfect fit. I saw reviews on a similar replacement complaining the display was too dim. This display is not. In fact, I think it is brighter than the original. Very happy with the results.

To my eye, this screen looks identical to the stock display that came with my Tab S7. Touch and S-Pen both work perfectly after replacement. This has given my tablet a second life. Replacement wasn't too difficult, just gently heat up the old screen with a hairdryer and drip in some isopropyl alcohol to soften the glue. Then I used the included suction cup to lift up the screen while using the picks and pry tools to slowly cut through the adhesive. There are a couple of ribbon cables underneath the screen that need extra care so as to not cut through them. Once I got the old screen off, I carefully moved the wacom pcb and ribbon cable over to the new screen and stuck down the pcb with some of the included double sided tape. It is also extremely important to make sure that all of the old glue is removed from the frame of the tablet before putting in the new display. I used some B7000 adhesive that I purchased separately to glue down the new screen (after testing that everything still worked). There are plenty of youtube videos that show screen replacements on this exact device. Watch them and take your time.

Arrived well packaged and perfect condition, all worked.

Achtung. Samsung Pen funktioniert nicht richtig schreibt unkontrolliert