Dongar Dashcam Power Adapter (10-pin Type D) for Mopar Vehicles. Compatible with RAM, Charger, Challenger, Grand Cherokee, & More. Connects to Rearview Mirror, Built-in USB Power Source, Easy Install

Worth the money for clean install. This worked great in my 2020 Dodge Challenger SRT Hellcat for a dashcam mirror tap. Ease of finding power and ground preserving all OEM wiring, plug and play, and clean esthetically pleasing to the eye with no wires running from traditional power sources in the windshield making unobstructed vision while driving. Powered on when vehicle is started or in ACC, off when key turned off making it perfect for dash cameras and radar detectors.

Works great and took maybe 5 minutes to install. I did not expect to receive the actual power cords but those came with the adapter as well. Definitely worth the money., great quality, comes with power cords for different devices and a tool to install and hide the cables from your dashcam.

I bought this to install a dash cam in my 2024 Dodge Durango. This adapter is awesome and made installation a breeze. Once you pop up the two plastic pieces from the mirror (that was the hard part), then it only takes a few minutes to get everything connected and up and running. Great product!

I installed this in my Ram 1500 for my dash cam and it was nice and quick and easy. No more long power cord going to the cig lighter yay. Works flawlessly!

First, do NOT buy the suggested right-angle dongles; this kit comes with 3 dongles, each with a different male connector, which is good, because the suggested ones I ordered were the wrong connector.I wish they would have clearly stated this; it would have saved me a few bucks.Also, your camera will only be powered on when your car is running or in accessory mode. If your camera is so equipped and you want it to be usable as a “parking monitor”, this is not the kit for you.The kit comes with an orange, plastic trim tool that made removing the cover off my 2024 Ram’s rearview mirror easier.Following are top tips for 2024 and later Ram 1500 owners: the rear view mirror cover is in 2 pieces (a top and a bottom); removing them is the most challenging part of the install, but it’s not too bad. Read on for a good method to use.Note, the upper cover has a small section that slides down very slightly from the head liner; slide it down.Remove the top piece first, by slipping the small end of the tool into the lower edge of the top piece (about an inch or so up from the bottom edge) and pressing a tab (which you can’t see…) and pulling gently but firmly down. It’s not too hard to find. After getting one side done, do the other.Then, use the same tool to help gently, yet firmly pry the lower cover down towards the dash. If you jiggle the cover, you will see where the resistance is, and it consists of two “bayonets” and slots, one on each side of the mirror stem, that you must uncouple.That’s the “hard part”. After that, unplug the mirror by pressing the tab of the plug up and pulling the plug. If you look at the part that will be plugged in from this kit, it will make sense.Then re-terminate the mirror plug into the adapter, find the correct dongle from the 3 choices, plug it in to the USB and then your camera, power on your car’s accessory mode, and test your camera.Don’t adhere the USB port to your window yet!After confirming function, tuck the wires into the lower cover, making sure to feed the red and black wires thru the small slot on the side (Ram must have anticipated this), line up the “bayonets”, and press the lower cover into place.Line up the tabs on the upper cover and press them into place, then slide the “movable” part of the cover towards the headliner until it’s flush. Find a good spot to adhere the USB port and you’re done.

Works great but the instructions for my 2019 Ram 1500 were very confusing and I ultimately just had to go about it myself. It was easy to install once I realized what I was doing. It also works great and love how it now hides my cables and turns on with my vehicle.

Only issue was getting cover off the mirror electronics. Other than that a 5 minute install and works to clean up cables.

Worked great on 2025 Ram RHO lvl 1 digital rear view mirror.