Aleratec Motorized DVD CD Disc Repair System - Playback Restoration and Cleaning Device for CDs and DVDs - Includes Repair Solution - Portable Cleaner for CD Player Discs with Read Errors

This worked great to fix a problem where the dvd wasn’t being read on the computer. Needed to use the “cleaning” procedure twice outlined in the manual to fix the issue.

Very easy to operate and does a great job of cleaning. It will not repair corrupted discs, but if you have dirty discs or light scratches it will do the trick

The original importer and seller of this product, Aleratec, closed their business a couple of years ago when the CD/DVD duplication business dried up, so there is no product support or warranty from that company. That being said, if you receive a defective or damaged product, you can probably return it to the current seller for an exchange or refund. This particular item is probably closeout inventory which explains the low price, but I had purchased other products from Aleratec in past years, and everything they sold with their name on it is quality, including this item. I received product yesterday, and like so much else that comes through Amazon these days, in was in a shipping bag, but the cleaning device is in its original retail sales carton. It operates similar to other disk cleaning devices, and I had a chance to try it out on a couple of DVD's that stopped playing. Most of my DVD collection is "hard to find" items. The first disk, after cleaning only, played flawlessly after just one pass. The second DVD, after cleaning, still had a few skips where it was scratched and pitted in a few places from improper storage container, so I ran it through the full 3-stage process: clean, buff, and "repair" (polish), IN THAT ORDER. The DVD plays, fine, but a couple of minor skips, with most of the damage removed. I believe after a second pass to cut a little deeper, it will play at 100%. The instructions are adequate but as others have pointed out, if one has never used a disk cleaner before, they are a little hard to follow, so read and re-read a couple of times. Here are a couple of tips: Run the cleaner cycle first, in some cases it is all you will need. My kit came with 3 wheel bases, and a cleaning fluid reservoir, which is the wet base for when you running a cleaning cycle. All of the other pads will fit on a wheel base. A little plastic tool with a prying tip is used to lift one of the spring-loaded pads off of the reservoir base. Be sure to sue that prying tool so you don't accidentally pull the retaining ring off of the cleaning pad. You only need to remove one pad to fill the container. The instructions say to fill 80%, but about half way is adequate for several cleanings before refilling. Be sure to remove the cleaning reservoir from the machine when you are done so it doesn't leak into the machine during storage. For deep scratches, you will need to run the second stage to buff off the surface of the disk using the buffing pads. There is no liquid product involved, just the coarse buffing pads. After the buffing process, you will have to run the polish stage ("repair") which fills in the swirls left by the buffing pads, living a film on the surface of the disk which makes the swirls almost invisible to the optical ready. At this point you are finished. If you decide to repeat the process for deeper scratches, be sure to run all three steps starting with cleaning, because the disk will not buff properly with the polish material still in place. Then run the repair cycle again after buffing. All of this is mentioned in the instructions, but it is not explained very will. I rated this product 4 stars because there is no product support however the price is a bargain for the product quality and it works if used properly.

Everything works great for cleaning but the repair kit is crap they put 2 dry pads and no wet pad in my kit so I have to deal with it or drive 30 minutes (I'm physically disabled so not easy for me) just to return it.... Definitely not happy

First off I see a lot of reviews with people having issues. I don't know if they are reading the instructions or not but you definitely have to read them. This thing fixed every single disc I have used it on which is pretty good because I didn't think it was going to work. I only used it on a couple of discs so I can't speak about the longevity. First thing you should do is get cotton pad with rubbing alcohol on it then wipe the disc with it. Use circular motions. Then use the included (or another one laying around) fine small microfiber cloth. Don't use the other microfiber with the bigger strands/bristles that's for applying or removing wax or cleaning windows. Make sure you wipe from the center out when using the fine microfiber. If that doesn't fix your disc and stop it from skipping then you should use this device. This thing isn't magic and it can't fix really bad discs. This thing does leave scratches on your disc so if that bothers you then shouldn't use this product. I have a large collection of all kinds of discs and this thing is a god send. I love this thing and it is very fun to use for some reason. I just hope that it lasts.

I've rewritten this review to reflect my latest experience. Just know up front that you may not be able to save your CD, but it's worth a try. As the Three Stooges once said when they were "doctors": "We kill or cure!" Same with this machine! First, about CDs, DVDs: The "playing" side is the thickest part of the CD, with clear polycarbonate meant to be scanned through to read the "pits and lands" at the data layer. The label side of the disc is the thinnest and closest to the data bits. If the label side is scratched, the disc is probably a goner because it's probably reached the data bits. If you hold a disc to the light and can see holes through it, you're probably out of luck unless they're very tiny holes your player can correct for. If the scratches are only on the playing (silvery) side, then you can probably fix it if you can polish or buff your way through the scratch (if it's not too deep). If you're looking for a simple, one step solution to all your unplayable optical media, this is NOT it! If you just want to keep it simple, try washing the disc in the sink, or buying another one. Or take your disc to some place that sells used CDs and see if they have a professional machine to take the scratches out. If you're patient and willing to work with a machine that's not perfect and work within its limitations, keep reading to see what I've discovered. There are much more expensive and bigger machines here that get the same complaints, so you might as well take your chance with this little thing and pay less for it if you're patient and willing to take a risk. First, this machine seems to do OK with very light scratches (the kind your player can probably read through) with the "repair" and "clean" pads (yellow and blue). Three very small drops of the repair "sauce", and one run makes it nice and shiny. As for the "clean" (blue) pads, they just use isopropyl alcohol to clean the surface of the disc. If you're only cleaning one disc, don't waste the solution by filling the reservoirs, just put a few drops on the small blue pads and go. If all you have is finger smudges on the disc, you can wash it in the sink with hand soap or dish soap, and you're good to go. What about deep scratches? For those, you'll want to pull out the red "buff" pads, and they will likely make your disc unreadable. So, if your disc plays but it's just ugly, don't use the red pads. Other reviews here say one pass with the red pads is OK, but my CD needed much more than that. Start looking for a new disc, and be prepared to give your disc up for dead before you pull out the red pads! I have two disks I've run through this machine. One was severely damaged with lots of tiny pits, and I had at first tried using sandpaper followed by Novus polish. (You can find this method on line: Start with 1000 grit wet sanding, and work your way up to 7000 grit, then polish to make it shiny again.) This manual method still did not take off enough polycarbonate to get all the damage, but did not introduce any new errors, at least. This was an audio CD, and the tracks that were good before I took the CD to hell and back were still good, and the ones that were bad before were still bad, though the disc was uglier after the process. So, I did several rounds with the red pads, and then took it through the yellow and blue, but I knew it was bad when I saw severe clouding in the inner (where the TOC and important data is) and outer edges of the data area. So, now the CD is completely unreadable. My advice: Never use the red pads unless you've already given the disc up for dead, because it'll take a miracle or a lot of manual intervention to bring it back. If one pass with the red pads doesn't fix it, be prepared to go the manual wet sand route. Anyway, the good news is, I had another CD with a deep scratch that I also wanted to fix. It was the worst kind of scratch: An arc right in the direction the disc spins, which affects too many bits for the reader to correct. I learned my lesson about the red pads, so I went with the manual sandpaper method above, which I had to do several times to get the scratch out. Finally I was done, but the disc was hazy after all that "torture", even though it now read the problem track. So, I ran it through this machine using only the yellow pads and washed the residue off under the sink. Now the disc looks almost new, and reads every track. (Your mileage may vary, of course!) Use this device with caution, and realize you may have to manually intervene to save discs with deep scratches. Also, if you're ripping or testing audio CDs, all that sanding and polishing may introduce other, hopefully correctable errors. For the most part, if you can avoid using this machine, do so. Try washing the disc under soap and water first. Most players can read through light scratches or correct minor errors, especially if they go from the inside out. If they follow the curve of the disk (like the pickup scratched it), you may be out of luck. Deep scratches may need the yellow "repair" pads and solution (sparingly, three tiny drops). You may need to be a skilled craftsperson with fine sandpaper to fix the really bad ones. If I do manage to save the ruined disc, it won't be thanks to this machine. The only reason to try to save a CD with this machine is to save another piece of polycarbonate from the landfill, and avoid having to buy another one if possible. Collectible and Out Of Print CDs will be worth less after taking them through this process, but if you succeed and make them playable again, that saves you from hunting for another one and paying through the nose for it, doesn't it? If you're handy with tools and like to invent hacks, I could see how this machine could be a platform for improvements, such as making it take fine sandpaper and polish pads.

The Aleatec dvd cd repair system is a very useful product. I have over fifty dvds that needed cleaning/ repairing. This system really does a very good job. I’m happy with this item.

I purchased the CD/DVD cleaner as I need something to clean off finger prints and hopefully fix some of the light surface scratches. I was excited to receive this one as quite a few reviews were positive about it, but I had a lot of trouble with it. When I received the product, my box came in crushed in the left corner which Amazon had taken care of it for me. I immediately started to read the instructions and learning about the machine before I started to play around with it. The product is easy to use, but I couldn't figure out how to use the deep buffering pads (probably a blessing in disguise). Switching between a cleaning pad and a repair pad was easy enough. When I first used the repair pads, it seemed to work great (it was about 3 or 4 times I used it) and the cleaning pads did an ok job too. But as I would use it here and there, the machine would start to damage the discs. When I would repair them, they would cause a haze on the disc and deep swirl marks, so I would use the cleaning pads and that would cause even more swirl marks and a water type stain. I tried this a few different ways and still receive the same results and now with damage discs. I called Amazon and ask them about the machine, since I was in the 30 day warranty. They asked if I had contacted the seller. I told them I called the 800 number in the manual and it takes me to someone's personal voicemail that says "This is the CD/DVD repair company, please leave a message". So I did, got no response. Then Amazon directed me to contact the seller through messages on Amazon. I did, but the seller would take days to respond and the seller's last question to me was "what kind of discs are you using?" I replied DVDs and have yet to hear a response from the seller and it's been over 2 weeks now. So after getting no where with their so called Tech Support or the Seller themselves, Amazon sent me another one out and told me to discard the original one. When I received the new unit, it was doing the same thing, causing deep swirls on the disc and a haze all over the disc. I had to speak with Amazon a third time to get the one sent back for a full refund, so I could try a different machine and company. I know the manual says the repair pads have about 20 uses before it goes bad, and 50 to 100 uses for the cleaning pads but I never got to reach those numbers before they destroyed the discs. Overall, I would personally not recommend the cleaning product. Go somewhere else or get a different company, this so called Company doesn't care about it's consumers, just the money it can rake in for a faulty product.