💖💖💖You can purchased bike rear light,bike saddle,phone mount holder,handlebar tape from us if you need.Twist lock type matellic axes:✅This structure can guarantee concentricity and depth of parallelism of two side BB bearing. It also can fix accurately position relation of two side bearing.✅1. It can bring more stable combination between frameset and BB;✅2. Filtrate and absorb deficiency of concentricity and depth of parallelism for Bracket Bottom port on both side of the frame set. And it can guarantee that crank run more smooth and transmit riders’ output power into chain to the Maximum limit, then convert to drive forward momentum.✅Plastic steel shell:✅It is a kind of plastic and steel texture character that allows suitable deformation, but does not damage its rigidity. It also can absorb roundness tolerance for installing ports of Bracket Bottom.✅1.It can protect Bracket Bottom of the frame to the Maximum limit;✅2.Filtrate and absorb roundness tolerance deficiency of the Bracket Bottom port. And it can guarantee BB bearing operation in standard roundness tolerance. It also can make BB more smooth, and more longer service life.✅Use new design,screw-in type in two side,threaded design eliminates creaking.✅Dual silicone seal keeps the contamination out for longer life.✅BB lubrication is similar to ceramic bottom bracket.✅Tips：1.Before you press the bottom bracket into bike frame,you should coated with oil on bottom bracket and bike frame.✅2.you should press the left side into frame,then press the right side into it(the right side is plastic cup)✅3.the last step,screw into the right side of metal part.✅Product FeaturesMaterial: composite, steelRecommended Use: Road Bike and Mountain BikeShell Width: 86.5-92MMWeight: 105 gManufacturer Warranty: 2 year
J**.
Super Upgrade - Great Improvement
This is a great solution to replace the terrible press fit bottom brackets - which are inherently prone to making lots of snapping, clicking and popping sounds. This BB is very smooth and quiet....simple and easy to install properly. I installed it on a 2014 Giant Trance - an amazing upgrade compared to the OEM press fit BB trash.
N**5
Came with spacers but no instructions
My trek has bb91 aka bb92 bottom bracket with press fit bearings. I had upgraded to an enduro bb with replaceable bearings but that's usually not my issue, it's the creaking of the press fit shell. So this looks interesting in design/concept, it's more of a 'pull fit' than a press fit. There's a red endcap included with this that just falls out when I push the crank through, not sure if that's needed somehow. There are 2 spacers and a wavy washer included which mine doesn't have, but probably needs, on the drive side.Ther are 2 'mushroom cap' cover/liners which covers the outer bearings from dust and also lines the inner bearing surface which the spindle rides on. I don't like this, in a few years this will disintegrate and I will have to trash this whole unit.
R**D
Might be good.
I have to agree with Peter The edge is very thin for the tool. If you don't have the right tool it's going to be a pain in the butt or you're going to damage your frame or the bracket.I like the original on my bike which had a 24-in bearing on the drive side in a 22-in bearing on the non-drive side this one is 24 and 24. It includes a coupling that reduces 24 to 22. It doesn't seem quite as snug as it should. I'll check back in when I put some miles on it.
H**S
impossible to remove
Worked great, easy to install. I just snugged it up being careful not to over tighten. However the teeth on the outer edges are very very soft. I srtipped the drive side like it was made from butter when trying to remove it. I took it to my bike shop. These guys know their stuff. They stripped the other side instantly and with the proper shop grade tool. Now I have a 7000.00 bike with a stripped bottom bracket stuck in it. Im going to have to cut it out. Do not buy this product. Its a serious headache upon removal. Super frustrating
J**.
Buy extra spacers.
Make sure you have extra spacers. I had to add some. I have about 100 miles on it. Seems to be working great.
O**O
Good BB
I was skeptical because I've mainly ever used Shimano or FSA, At first it seemed flimsy, but once on the bike, its perfect. It does exactly what it needs to do. Good BB and will probably be going on my next build.
D**N
Great product for the money
Fits very precisely, snug, and doesn’t creak. Excellent quality and finish. Very good product.
M**W
Ease of installation
Worked as advertised. Fit into PF 30 good no complaints on installation
