BLACK+DECKER 20V MAX Cordless Drill and Driver, 3/8 Inch, With LED Work Light, Battery and Charger Included (LDX120C)

Don't know why I'm reviewing this drill. I guess it's because after reading all the other reviews prior to buying, I'm somewhat conflicted since mostly, people either seem to love or hate this drill and I'd like to get my two cents worth in. After reading about a bazillion reviews (small exaggeration) I didn't know what to think and, I thought perhaps I could help my fellow Amazonians (is that a word?) make a buying decision based upon my own, hopefully informed opinion. While I am not an expert, I do build and sell hardwood furniture and am familiar with most of the tools that you would find in a working woodshop.I was surprised by all the negative reviews. It seems that a lot of folks are having problems with this drill; chuck failing or not holding bits properly, overheating and smoking, charging issues or battery not holding charge for very long, etc. One of the reasons I bought this drill was because I was somewhat titilated wondering if it was a worthwhile purchase or not. Since Amazon has return priviliges I figured I could examine the product thoroughly upon receipt and decide for myself if it was a good buy.I thought that this drill looked interesting. To me it looks kind of "cartoony" (there he goes again; making up words). With its bright colors and swirly lines it looks like something Roger Rabbit would use (or, if you're in my generation; Bullwinkle). If you'll note in the first photo below, the barrel is somewhat shorter than the average cordless drill. It is attractive; I like the look of the new flat battery packs as opposed to the older, clunky "stick-type" batteries. I noted that this drill is 20V which, you would think would make it more powerful but, in looking at the torque rating, it's not necessarily so.Now, just to make a comment on one of the most frequent complaints in other reviews. A lot of reviewers are complaining about the bit not being held tightly in the chuck. Firstly, take a look at the the second photo below. Please note that the icon of the screw is uppermost on the barrel. This is important when chucking in a bit as it ensures maximum torque and tightness. If you have "10" or any other number at the top of the barrel, you are in a "torque setting" which is used when driving screws. This means that when you achieve a certain tension, the clutch will slip and fail to tighten the chuck further. If you hear a clicking sound when tightening the chuck around a bit, then you need to adjust the ring so the screw icon is on top. Also, note in the photo, that I am wearing leather gloves. Frequently, when hand-tightening the chuck, it will escape your grip (after all, we're not as strong as gorillas) and spin, burning your hand. Because of this, most of us don't exert all the pressure we're capable of. With gloves protecting your hands, if it slips, you don't get burned and you're capable of tightening your grip and getting maximum holding power between the chuck/bit. The holding power of the chuck is dependent entirely upon the tightness of "YOUR" grip when inserting the bit and holding the chuck ring. I think that the majority of the complaints pertaining to this problem would be solved if the above two suggestions were followed. Nothing in the construction of the drill I received would lead me to believe that it is some kind of manufacturing deficiency.Upon unboxing this drill at a friends house his wife thought it looked "cute" and felt it would be a good addition to their kit (they frequently go to numerous flea markets throughout Texas and carry basic tools with them). Being smaller, it would take up less room in their trailer. You might have noted that I mentioned this is a good womans drill in my title blurb. The reason for this is the drill handle being smaller than a normal battery operated drill. It's still big enough for a man but, being smaller, it will be easier for the average female to handle than most drills. It is also lighter than the average drill which, I think most women could appreciate.I decided I would test this drill for both overall power and battery life. To do this I decided upon a series of tests of what I felt were of gradually escalating difficulty. While these tests may be pertinent to my particular situation, only you can decide if they are a "fit" to your situation and expected usage of the product.Incidentally, for my tests, even though I typically use hardwood, I felt that since White Pine is the lumber that most homeowners commonly use, it would be more appropriate for my tests and, since 3/4" stock is far and away the most common lumber that I would utilize this thickness. My results were as follows:Drill Three 1/4" holes through 3/4" stock with a brad point bit - AccomplishedDrill Three 1/2" holes through 3/4" stock with a brad point bit - AccomplishedDrive Three 3/8" Lag Bolts through previous 1/4" holes in 3/4" stock - AccomplishedDrill Three 5/8" holes through 3/4" stock with Forstner Bit - AccomplishedDrill Three 7/8" holes through 3/4" stock with Spade Bit - AccomplishedAt this point, I was expecting the charge to be gone from the batteries. Using a spade bit is difficult and draining on any drill. So, I decided to up the ante; I increased the size of the spade bit to 1 3/8" (a very large hole indeed) and the stock thickness to 2" stock (nomimal 1 5/8", a two by four). My intention was to continue to drill holes to the point of refusal of the battery to rotate the drill. Results as follows:Drill 1 3/8" holes through 1 5/8 " stock til failure - 3 1/2 holes AccomplishedNow, to be truthful, when I stopped, the battery was still rotating the chuck and bit but, it was starting to bog down. In other words, battery failure was imminent. Could I have finished the 4th hole? Yeah, probably I could have abused the tool and forced it to finish but, it didn't have much left. Also, even though I was wearing leather gloves, I could feel a lot of heat at the barrel (after all, these tests were done with no interruptions) and it was apparent to me that to continue, I would probably smoke the motor, which made no sense to me. You can take my word for it; This drill would not have finished a 5th hole without catastrophic failure. By the way, I do not recommend using spade bits with a hand-held drill. They are particularly hard on a drill and, although I rarely use them, I only use them in my drill press. The only reason I utilized them in this testing was because I knew they would put a substantial drain on the battery. Especially using a large diameter bit like the 1 3/8" comes very close to the definition of abusing your tools so, if you can avoid it, I suggest not subjecting your drill to loads such as this..Conclusions: I believe that this is drill that is well suited to the home handyman. Would it be a good drill for a professional that needed it for use daily? Probably not, although it might last a while. I also think a pro would want a drill with a little more torque and definitely more drilling speed. However, even though the listed torque is low, while I was drilling the largest holes with the spade bit, when it caught in the hole it had enough torque to spin my wrist around (and I'm 6'4" and 210 lbs) so, it should be adequate for most of us. I also think that because of it's reduced weight it would be an ideal drill for a woman and I think the manufacturers did a good job of "splitting the difference" in designing a grip that is both large enough for a big man (though just barely) and small enough to be comfortable for the average woman.Caveat: As I told you earlier, one of the reasons I got this drill was because of all the contradictory reviews (it piqued my curiousity). I think almost 20% of the reviews have some complaint about this product. If you do decide to purchase, make sure that you do test and inspect your drill closely to make sure that none of the issues mentioned in other reviews are present in your purchase. Based upon the product I received, it is apparent to me that Black & Decker is capable of making a quality product however, DO inspect yours prior to the expiration of the return window. With this caveat, I can recommend this cordless drill.I hope that this review, since it addresses issues outside of others comments, was of some help to you.

Tengo uno de la misma marca de 12 v y aunque me ha sido muy útil, sentí que le faltaba más potencia. Este por el contrario, aunque no comparable con los “profesionales” hace de todo sin esfuerzo.. lo recomiendo

I'm extremely satisfied with my Black+Decker 20V Max Cordless Drill! As a DIY enthusiast and homeowner, I needed a reliable drill for various projects, and this one delivers.The drill's ergonomic design fits comfortably in my hand, reducing fatigue during extended use. The 20V max motor provides ample power for drilling through wood, metal, and plastic.I've used this drill for hanging shelves, assembling furniture, and drilling into concrete, and it has performed flawlessly. The keyless chuck makes bit changes a breeze.One of the standout features is the battery life. I've gotten several hours of use on a single charge, even with heavy drilling.The drill comes with a compact charger and a carrying case, making storage and transport easy.Overall, the Black+Decker 20V Max Cordless Drill is an excellent choice for DIYers, homeowners, and professionals alike. Its reliability, power, and affordability make it a valuable addition to any toolbox.Rating: 5/5 stars

Very good for the price

Muy útil.

I bought this as a Warehouse Deal, in the original box with a couple of scuffs, for $30 with free 2 day Prime shipping. My use is on my workbench for various drilling, brushing and cleaning jobs, as well as driving small fasteners while using the clutch. It's a second drill driver to supplement my Hitachi 10.6V unit, which has served me well for quite a few years now with no failures. My first impression of the unit is that it's certainly not commercial grade, but it's performance is impressive thus far. Very powerful and torquey for it's size and price. A nice touch is the wide base which makes it very stable when set down, not top heavy at all. The lithium ion battery is a vast improvement over the older NiCad technology, lightweight and powerful, and very forgiving of less than attentive battery charging habits like leaving it partially discharged between uses. It has a slight lag between trigger pull and motor start that takes a little getting used to, but it's a fraction of a second and not a big deal or time waster. The clutch is OK and does the job quite well; the chuck is of decent quality too. It lacks some features of more expensive units, like dual speed ranges and a higher number of clutch positions, but the gear ratio provided seems like a nice compromise between speed and torque. Overall, it's compact and lightweight, and a perfect fit for the bench work I do. The battery charger design is a bit less than optimum, somewhat cheaply made and requiring 2 hands to connect the battery to it, again not a big deal but a "drop in" charger is a better design and my personal preference. I honestly had not planned to buy a second drill driver for my bench, but at the price I couldn't pass it up and it allows me to have 2 drivers set up for different uses, and thus saves time by minimizing bit changes. My 5 star rating is based on ease of use, build quality, and power versus size and weight, and the very low price paid for a tool that will be used daily for years to come. I'm very pleased with it thus far as an "entry level" drill driver; it's just what I needed. It also bears mentioning that the compact size and lighter weight make it a great fit for female users, or anyone who wants good performance from a very compact and easy to handle, yet quite powerful, drill driver.Update 05JUL22: I've had this drill driver for about 5.5 years now, and thought that updating this review would be appropriate. I use it several times a week typically, so it has accrued a lot of hours and handling. Still works like new, even the clutch which sees a lot of adjustment for various driving jobs. Battery still holds a charge like it did when new. The compact size and light weight of this tool really make it shine for day-to-day light duty work. For the price paid I can't gripe about a missing low speed / high torque setting, but if there's anything missing it would be that. I expect several more years of use out of this drill based on its current condition. I wish every tool I own gave me this much value for the price paid. Will buy another if this one ever wears out or fails. The Hitachi I mentioned earlier in this review (Model DS10DFL) has suffered a broken clutch detent spring at about 10 years old, and while waiting for parts this Black and Decker is substituting nicely.