3PCS Creality Original Ender 3 Heat Bed Platform Sticker Sheet, Ender 3 Pro Hot Bed Build Surface Tape 235x235mm for Creality Ender 3 V2/3 V2 Neo/Ender 3 Neo/Ender 3 S1/Ender 3 S1 Pro/Ender 5

As others have stated, this is the sticker sheet on top of your bed platform. To clarify, my bed platfom attaches with 4 clips (original Ender 3). It's flexible, but sturdy. I didn't realize it, but it's actually 2 parts - this sticker and a plastic sheet below it. This one fits great and is an exact replacement - just be ready for QUITE a bit of work getting the old one off and removing the glue residue from the plastic base (the harder, but still flexible portion of the bed platform). Nail polish remover and a PLASTIC razor blade (doesn't scratch the surface) worked for me to get the residue off, but it took some time to get it all off. It has to be squeaky clean so the new sheet goes down with no bumps underneath. Remember that your print layers go down in fractions of a millimeter, so the bed has to be absolutely flat for you to get great results. Take your time and the glue will eventually all come off. Super sticky when the new sheet goes on (one shot and it's done - no second chances). I used the screen saver install method of lining everything up and taping one edge of the new sheet to the base like a hinge. That way when you peel the backing off, it will go right into place. I'm glad they come as a 3 pack as my first attempt without using the tape hinge didn't line up correctly for me... I've done a couple of prints since the change and they stuck great to the new surface. Overall, I'm pleased with the purchase. For some additional info, search "What's the stock bed on the Ender 3 called?" You'll find a discussion and even a video that helps provide more clarity.

I have been using a print surface like this for years, then I saw the PEI magnetic build plates flood the market about a year ago or so. I bought one and tried it. It seemed a little finicky but overall it hung on to the print while it was printing and then it was easy to get the print off the bed when it finished. I bought another one for my other printer. I have a cartesian printer and a delta printer. After about a year the honeymoon was over. I don’t know what happened but bed adhesion just about went away. On the delta printer it was like anti-adhesion. I tried hotter, cooler, faster, slower, higher, lower, wipe it with IPA, everything I could think of and it just wouldn’t stick anymore. The PLA would stick to the nozzle, not the bed. I had some of these laying around and I tried one. I reset my z height and printed a test. What a difference. My nightmare was over! Yeah, the prints are a lot harder to remove now but now I see that as a good thing. Patience is a virtue. Like some other reviewers have stated, these have very good bed adhesion. Almost too good. Be careful when removing the print that you don’t exert too much force on the print and lift up the sheet and make a bubble. Then the bed isn’t flat anymore. You might have to wait for a few minutes for the bed to cool down. And the sticky side is very sticky. I stuck mine to a glass plate, then clipped that to the bed. Nothing is flatter than glass! I bought some more of these and now I am stocked up. I don’t have an Ender but I can trim these to fit my printers with scissors. I figure these last for 3 to 6 months, maybe up to a year, so I am set for a few years now. I will never stray again – lesson learned. EDIT: I ended up applying this build sheet to a PEI spring steel plate. Now I have the best of both worlds. I have the strong bed adhesion that I like and when the print is finished I can pick up the plate and flex it and the print will pop off.

Worked but still had slipping when printing

So my original Ender 3 bed had too many dings in it and it was time to replace. I picked the cheapest 3 pack I could find on amazon with prime shipping and crossed my fingers expecting the worst. But the adhesion on these things is excellent so far. I'm printing with PETG and on the stock PEI surface I needed 70degC to get reasonable adhesion and the parts could be pulled off the bed by hand after printing. With this surface I'm printing at 40degC and I have to use a scraper to get the parts off. Next I'm going to try not heating the bed at all. So far I'm a dozen prints in and it's been consistent. FYI the adhesive on these things is incredibly tacky. After removing the old PEI sheet and cleaning the bed surface you only get one shot at putting this thing down. If even a small spot makes contact you will have a hard time removing the sheet. I also have a cheap rubber brayer that I used to really press the sheet down onto the bed surface.

easy to use

Ottimi tappetini Consigliati

Bought these on the off chance they work with ASA. They do, absolutely fantastic for ASA. Will buy again when I need more

Recieved a few days ago, but after a weekend of printing high temperature filaments, the surface is warped and generally unusable. Adhesion was great, but now it is impossible to get a level surface

Identique a la description Exactement ce que je recherchais

nicht kaufen, besser aus Glas !!!!