VLANDTail lights Assembly Fit for Mitsubishi Lancer & EVO X 2008-2021(Not for Sportbacks/fortis/io), Rear Lamp with Starup Animation, DRL, Back light w/Fog Lights & Sequential Turn Signal, Smoked

I bought these after someone hit my 2010 Lancer DE and one piece of the OEM tail lamp was $100. I got the whole set for $150 and it’s awesome! Easy to run the wires. Just get the polarity right! I had one reverse light plug backwards and it made the reverse light red! They look great!

Purchased the smoked sequential tail lights. Happy overall though initially I did have some issues with the install, but it was in the end primarily the poor instructions and user error. Once they were hooked up I found the visibility to be suitable and the overall look and feel to be very good.Definitely helps to have a functional and “UN”smoked center light for consideration of others on road in low vis conditions.Did not need to use ANY resistors though I left one 3M’d to the trunk and purchased two additional sylvania from autozone..Just needed to marry the left inner trunk light to left.Had issues finding some of the wires since instructions were not very helpful whatsoever.Excellent facelift for my Lancer. It’s an 09 I’ve taken great care of has 72K and borla exhaust and other upgrades as well. Pedal controller sport brakes new struts and more.The overall value is 9.5/10Also others criticisms I had to somewhat laugh at as 3rd party will never be as “great as” OEM. These are close.I used to have vland sequential LED headlights but a wire came loose and wasn’t discovered until I “re-re-replaced” them with stock look ones. Tossed the vlands, since the headlights visibility wasn’t very good and the stock ones were. Plus, they were a bit too flashy, especially for how weak the power output was with even highest tier bulbs.The wiring is weird at first because the outer trunk lights have two totally different wiring outputs from the vehicle!! I destroyed part my trunk liner looking for wires that were simply tucked in my left inner trunk bulb..Even after several YouTube videos it really just took a lot of putting the pieces together and pulling them back apart and cautiously examining everything from a true “engineering” aspect.I frequently take apart and wire stuff at my job 5/7 days of the week, so I had an edge, but I was still confused because the wires in the inner trunk lights can give issue and become trapped particularly around the silicone ring.

I purchased the tail lights and headlights for my 2009 lancer gts. Everything was plug and play but the shop where I was getting my car painted lost the daytime running light wiring harness. I emailed customer service and they sent me a replacement. These lights look sick, especially at night. The up/down adjustment for the headlights were also very accessible with a simple open hood. I was a little worried about needing to take the bumper off simply to adjust the height because my bumper has semi permanent screws holding it up but a small ratchet fits in through the hood no problem. You do need to take the bumper off to install them though. All in all, great deal and service.

This really sets off the look of the car.The lights do stand away from the trunk deck a bit but it really just adds a new body line.There are a couple of old bulb sockets (rear) not used so don't worry. Also I don't know but I think orientation might matter so make sure black and white wires are lined up on the plugs.Took a few extra minutes to figure out how it hooked up at first but it went smooth after that. I wish I looked for a YouTube tutorial.

These vland lights are pretty neat and almost plug and play. However, there’s some caveats to the install process specially if you’re new to this thing. Install WILL require you to remove the bumper cover to get access to the bolts you need to remove to switch them out.As for bulbs, this is where the issues can occur. Not too much well written documentation is out there but these headlights may come with a retainer clip or green circular gasket cover. If you have the retainer clip, you can easily fit H7 or D2H/D2S bulbs no problem. If you have the green circular gasket however, docs say only D2H and D2S bulbs can fit but if you cut the green nubs on the inner side of the gasket you can fit H7 bulbs in. Make sure whatever bulbs you use will actually fit, specially if you’re using LED since some won’t fit the bulb openingsExtra thing to note, if you have a CJ (2008-2015) Lancer, you’ll need to use the additional acc wiring and fuse harness if you want the LED and demon eye to come on as your DRLs. If you have a CF (2016-2017) Lancer, you don’t need to plug that acc harness in since most models already have the J shaped LED DRL (though plugging it in is an option if you want the LEDs as a DRL too alongside the stocks). There’s also an extra wiring harness inside the cubby where the bulbs for the dual beam sit you can unplug if you don’t want the additional demon eye light on the projector.Overall, these are some nice headlights and will definitely stand out (at least if you don’t already live in an area with plenty of Evos or Lancers already using these lights). Only time will tell whether these are durable but for now, they’re solid.

Quedó muy bien en el vehículo Lancer

The media could not be loaded.  This isn’t my first time changing the headlights.The only thing I have disconnect is the one wire that connects both daytime running lights as they were staying in regardless of the car was off and locked.But they turn on when you flip the switch once before turning you headlights fully on.Installing the D2H bulbs were unclear but figured it out.Looks great and so glad that we finally Come to a quick plug n play solution.

My grandson wanted these for the sequential turn signals.

Exacto lo que viene en la descripción del producto, llegó antes de la fecha de entrega y muy bien embalado.

Fácil instalación, calidad excelente, 10/10

Just installed these, they look awesome and give the car a nicer look, installation was not that hard if you fellow the diagram and video guides online, only con i can give for these is that the reverse light turns off after 5 seconds, easy fix you need to order a led load resistors 50W 8ohm 7440 plug in play and that resolved the issue for me. Overall good quality, worth it.

Es un buen producto, le quedaron super bien a mi auto sin tener que modificar nada, llegó muy rápido, el vendedor muy amable y responde todas las dudas

Looks perfect on car. Love the light on animation.