2025 New 3D Printer Enclosure for Ender 3 V3 SE/KE/Ender 3/3 Pro/Ender 3 V2, Fireproof & Dustproof Tent Constant Temperature Protective Cover for Anycubic Elegoo 3D Printers 25.6” ×21.6” ×29.5”

I struggled to get this together only because the enclosure was so tight around the frame. I ended up heating up the corners of the frame with a hair dryer. Heating seemed to relax things enough to allow the cover to fit. It was a tight pull over the last corner even with the heat. This is my second enclosure and it is definitely a better quality than the first one I got. The exterior material is thicker and more sturdy. The canvas exterior material seems better quality than the rubbery exterior of the other enclosure I got. This one seems to be more air tight also...not so many pin holes. Overall I would buy this one again and probable will.

Assembly was simple. The "tent" was a little tight trying to get it on the frame, but it ultimately fit well without any sagging. An Elegoo Neptune 3 Pro fits in this enclosure without any modifications to either the printer or enclosure. The large clear door is nice to be able to easily see how prints are progressing. The only negative I have to mention is the zipper is a little tight in one corner when closing the door, but at such a low price point, it is expected. It may loosen up over time or I may add some lubrication to this area.

Not sure who was on the QA team when checking the tent measurements, but the tent would not fit around the frame once I got it assembled. I made sure all poles were in as far as they could go, but I could not get the tent on. In the process of trying to fit it, the seams on one side of it ripped and that told me that I was forced to do something about it. I was forced to cut about 1 inch off from several of the poles using my rotary tool, so I could finally get the tent on. Once I did that, it fit perfectly. Now my first 3D printer's environment stays around 95F+ when printing and my curling problem is mostly gone. I'm using a fridge thermometer to monitor the ambient temp inside the tent. It's magnetic, so you will see it sticking to the filament holder arm in the video. The top two temps are the sensors in my fridge, while the bottom is the ambient temp in the tent. I still get the occasional issue with curling or collisions because of leveling and heat bed temps as you may see in the video, still sort of learning and I had to abort that print, but you can see it is staying a nice temp of about 96F, despite it being placed right in the path of my A/C vent. Aside from the fitting issue, the only other complaint really is that there is not clear window on the top or other sides to allow light in, so I picked up these great little remote controlled lights and hung them onto the top bars. (In opposite corners) Now with a remote from the outside, I can turn on both lights with a single remote click and see how the print is doing. Because of the reflective material inside the tent, the remote works great to turn both lights on, despite them not being in line of sight with the remote or each other. I never have to open it to turn the lights on and see how it's doing. Just needed to run the usb cables up to the lights to always keep them charged. Except for the initial assembly issues, I'm pretty happy with this tent, but you will need to make sure you have space for it. The tent is very large and should house most printers that do not have lots of extended hardware like multiple filament spools and all that.

Wow, no smell outside, i have a bambu Lab A1, which is open, and its in my room, so whenever i use it it used to be so smelly because of PLA, and i think its bad for breathing, but this encloser is lifesaver, price is very reasonable, and very easy to use, easy instruction, also, it maintains the temperature inside, that is a big bonus for open 3d printers, as i used to a lot of warps before, now it runs smooth in my opinion, definitely worth it, in terms of pricing, and use.

This product is basically just a plastic pole frame over a canvas cover. Sounds simple in theory, but the designers made the measurements so incredibly close that it really isn't the slightest bit practical. Expect a minimum of an hour to put this together (I needed to take breaks for finger pain, and I don't have arthritis or anything like that). Ultimately I'd recommend pliers to pull the final corner or two into place, and a hammer to ensure that all the pipes have actually gone into their connecters, as the connector diameters vary wildy (some are so loose the pieces slide right apart, while others are so tight you won't be getting the pipe in without hammering). The most nonsensical part of the process is the zippers. You'd think, with as insanely tight this is, somebody would have considered the need for quality zippers to keep it all together. But these are the cheapest zippers I've seen on anything in a long time. Drag is awful, and naturally they constantly split due to the tight fit, compromising the entire structure. The stitches also pull nearly to the point of ripping in some places. Even a single inch worth of additional slack would have been enough for all of this to fit together without causing any functional issues, but the way it is now, the zippers basically aren't of any use. Last thing--Although I knew this enclosure was going to be big (I checked the measurements), seeing it in person is...good lord. The enclosure is more than three times the size of an Ender 3 pro, so, picture something larger than a minibar refrigerator. It would probably fine for a dedicated workbench, but it's completely impractical for desktop use. It took two attempts before I got one with all the pieces in the box. Sadly it looks like it's going back anyway. It's possible to get this thing put together and in use, but the zippers are a huge design flaw that can't be overlooked. I'm not a believer in the "you get what you pay for" excuse. Make a product of at least the minimal quality required for it to function, or don't make a product at all. It's not the consumer's fault what you choose to charge for it.

It may not look how described, mine had printed on the front flap "3d printer enclosure", otherwise seems ok, a snug fit to get the material over the frame but it can be done without modification. It serves the intended purpose.

Me ayuda bastante, mi casa es pequeña y evita el calor se disperse, o que las corrientes de viento afecten mi impresión Altamente recomendado !

The tent was enormous but functional Too bad I got a broken one.

Excelente caja, la compré para mi Viper Anycubic y le funciono genial

Yo la ocupe para una impresora Ender 3 S1 y el espacio de altura es bueno con un poco de sobra. Y a lo ancho de la impresora cabe toda y sobra espacio. Con respecto a la temperatura es buena. Se siente mucho la diferencia en lo caliente de la habitación cuando está con ella. Cuando el clima está caluroso y tengo que imprimir, trato de abrir una parte para dar ventilación y dejo la parte de enfrente abierta. Para realizar ajustes a la impresora si es incómoda tenerla puesta. Y la calidad de los zipers es mediana. Al principio no cerraban bien.