Garage Door Remote Universal for Chamberlain Linear Multicode Liftmaster Genie Overhead Door Craftsman Stanley Garage Door Opener, for 3089 893MAX 893LM 373LM 973LM ACSCTG GIT GICT GT912 MAT90 1050

This remote is one of the best purchases on Amazon. Works amazing. Once I figured out programming the DIP for gate.(You can only program one DIP)I purchased the two button remote open the gate to our neighborhood, second button for garage door.Garage door programming went fine, as described in the instructions.The DIP instructions for my gate code or not correct. Here is how to do it correctly. On your new remote press the learn button until the light turns blue pointed at your gate then press as many times as needed until the gate opens. Then press the learn code button again.

These are tricky to program but if you follow the directions carefully, it will work well.

I used it for a dip switch configuration. It works great now that I figured out the instructions. Here's a clearer version. 1) remove the battery compartment cover to expose the dip switches; 2) arrange the switches to match exactly the pattern on the original remote or on your garage door motor; 3) press the small red button next to the battery until the red (not blue) led lights up solid; 4) using the chart provided in the instructions, press the button you want to associate with your garage door the indicated number of times, for example, 12 times. Each time you press the button the led will flicker briefly. 5) When finished, press the small red button next to the battery again. The remote should now be programmed. Repeat for another garage door. Note: the garage door might open/activate when you are programming and you press the designated button for the last time.*****************Follow up: This device began malfunctioning after a couple of months with a brand new battery, now it doesn't work at all. Past the return date and made overseas, so no remedy. Waste of money. Do Not Buy.

It was so frustrating to get this remote and not have it work when the instructions seemed very simple. I finally ended up emailing the company and it turns out their instructions were printed wrong, once I had the right instructions it was very easy to program and have work.If your instructions for going into pairing mode say "hold program button till led turns blue" don't believe it. You press it and then when the LED light turns red and stays red it's in pairing mode. Do that, press the button on the instructions corresponding to your garage door model, push the learning button on your garage door motor, then it's all good.

Works great- easy to install

Works great! 😊

This remote works great and with no wiring. The two channels are convenient and control my older (1990' era) Chamberlin opener as well as my fairly new Chamberlin model too. You do need to read the directions and follow them. Don't miss the various # key entries. This would have taken me less than 2 minutes to program and install, but it did require me to change the 3-position dip switches on my Chamberlin opener to NOT use the center 0 position (switch MUST be either UP or DOWN). This meant reprogramming the other remote units and the car visor but that was easy too. If yours are already set without the center position being used on any of the dip switches, your setup time should be under 2 minutes.Some people had issues getting this unit to work, but I didn't and I would recommend this to others. It's a great price for a descent keypad that has great universal support.

I was probably jerking around trying to program the keypad for over 6 hours with the included instructions. I have the older Stanley opener with the 10 digital switches. Between the confusing 1111# and the 2222#, then figure out and enter my digiswitch 10 number code, plus #, it was a nightmare. I tried to get help on youtube but could only find the "learn" button videos. After 4 hours of frustration I had contacted Amazon to send the keypad back. The next day I was still determined to beat the little bast*rd so I started again writing everything I needed to do on a piece of paper. I finally got it to work once with the 1111# code, then tried to change code, DOA. Watching the videos I noticed that some keypads needed the code and another number or symbol to work. That led me to try the new code plus the # key and door opened/closed. Seller could have saved me a lot of time putting that little detail at the end of the instructions. It almost cost them a sale!

El control dice que es compatible con mi puerta pero no funcionaHasta un técnico vino y resultó que no sirve