GEARit 1/0 Gauge Wire (25ft - Red Translucent) Copper Clad Aluminum CCA - Primary Automotive Wire Power/Ground, Battery Cable, Car Audio Speaker, RV Trailer, Amp, Electrical 0ga AWG 25 Feet

fairly priced and nice quality.

This 0 gauge ground wire is fantastic. I was extremely pleased with the flexibility and pliability of it. I used it to run a battery cutoff switch in a van with a 5.4 liter V8. I was installing the switch about 7 feet away from the battery so I needed something that would carry as much power as possible with as little resistance as possible. The quality seems to be top notch. I definitely recommend this product.

For the price, this is great stuff but there are a few things you need to understand BEFORE you buy it so you are not disappointed. The negative reviews are not wrong in most cases and there are some caveats: 1. This is measured in Gauge (usually refers to metric size), not AWG (refers to current carrying capacity) and should be called out in aught if it were truly AWG. Gauge is a faux measurement IMHO. The "standard" is so loose and so not really a standard that understanding that right away is important. AWG (American Wire Gauge) is a strict standard and you know exactly what you are getting. Go pay twice this price and you'll get true AWG measurements. Don't want to pay twice the price? Then you're going to compromise. 2. The individual strands are brittle as mentioned but that doesn't matter. If you're terminating correctly, it makes no difference what so ever. Voltage drop, heating because of amperage or anything like that does not matter if you lose a strand or two. As a cross section of the wire it is just not enough to make a difference. 3. Yes the wire is on the stiffer side, that's a good point made by folks here. It's not bad actually, but figure your bends are going to be the size of a coffee can and maybe not quite as tight as the side of a coke can because it's stiff. Bottom line question: Is this 1/0 AWG (gauge?) Absolutely not. In AWG this would be just about 1 AWG on the thin side. It comes out at about 7.28MM which is basically thin 1 AWG (there is some margin of error in my measurements I'm sure). This is probably 1/0 gauge when you can measure "gauge" any way you freakin' want to. For this price, at this size of wire, you aren't going to do much better. Think ahead. This is a great buy for what you get, just get passed the marketing. I could not find wire this thick at this price on Amazon period and this was the best price by a couple bucks. Buy appropriately. I hope this helped!

I have a winch and already had a M/F plug for it so it wasn't always connected to my battery. I used this wire to make a huge jumper cable that could also plug into the feed from my battery. So when I jump a vehicles battery I can reach very far and I also don't have to pop my hood and connect anything. Its a sweet setup if I say so myself.. =) The crimpers and cutter was SUPER handy to have if you want a quality install of whatever you use this wire for. The wire itself is flexible and thick. The tools are quality. I would get again if I have some heavy gauge wire needs.

This is definitely value-priced, and it's nice and light (it's aluminum with copper coating, not solid copper) if your application will benefit from that. I have mine carrying some serious amperage from a solar battery array to a big inverter - no problems. HOWEVER - make sure you have some options handy for crimping terminals on this stuff. It seems to be in between sizes. My size-zero dies will let the wire slide right out, and the 1 is a bit tight, so I have been using the Zero and then 'snugging it up a bit' with the #1. That's my only gripe, and I'm OK with the compromise for the price, but if you had a particularly critical application in mind where that kind of thing would not fly, be aware before you pull the trigger.

Great item

length from battery to tail + cable routing to use for a Anderson power plug works for my project value for money worth it a new cable cuter and battery lug crimper and battery terminals well packaged set up. quality works it works good buy .ease of use easy to install why because every thing is fitting just right the copper content perfect. length from battery to tail exactly what i needed for switched Anderson out lit to work. Heat resistance strong wont have problem passed the 0:30s heat thing test

Good quality!

I'm very satisfied ☺️

This is the best wire that money can buy. It is thicc and light and very flexible. Everything that you want for a welding wire. Probably worth more than I paid.

Pour filage dans mon VR

As advertised. Nice and flexible. I would run protection around it, the coating is not very durable

Good value in my opinion. Quite a flexible product seems to be a durable coating on it.