JEACENT AC Window Air Conditioner Support Bracket Light Duty, Up to 85 lbs

Second purchased of this item one of my older acs kicked the bucket and the new one is just to heavy for my liking to trust the window frame so I searched for this. It’s easy to install.Sturdy and holds a 75lb ac with ease. The other one I have is 2 years old and still looks new. Well worth every penny. Make sure u have a 10mm wrench and socket you will need them to install this. Worst came to worst 2 pliers would work to but a lot more work.

Well made and easy to install bracket. I really like the fact that this bracket protects the bottom of my window frames from damage.

Great support my my new AC. Install was not to bad and works like a charm.

It's great. I am a 56 yr old female and I did it alone. Took me hot minute. But the stand works great.

I have 4 of these now. I bought 2 a year ago and they have made i stalling our air conditioners so much easier. We feel more confident sliding the heavy ac units safely onto the mount and are not over straining like we used to with the fear the ac could tip out the window when sliding the window down to secure it.We have a few different types of ac units. Our LG models sit flatter on the mount, while our Fridgadaire and Midea have a thin bar underneath that makes a half inch gap/opening to the outside when sitting on the mount. Be prepared to use that gray long window foam to stuff in the gaps and tape it with masking tape. That's my technique to keep the hot air and bugs out. Not a big deal at all. I use masking tape because it doesnt leave a lot of residue behind and stays in place most of the summer. Its also a tan/off-white color that is less noticeable than say green painters tape (gentle on paint, but an eye sore). Don't use white duct tape! Removal sucks and leaves so much sticky residue.Anywho, with our safety and fragile backs in mind, this mount was worth getting. The metal pegs are a bit cheap and pop into the frame now and again where its annoying to readjust them... but once you get the hand of it, it's not so bad. With 4 mounts now, I only had this happen twice. In place, they are totally strong enough for their purpose.We have 2 100 pound ac units that are way easier to I stall now. Our other ac units are around 55 to 80 pounds each.Thanks for this!

Window bracket is sturdy and works well. However, it will leave pretty large gaps (1-2 inches) between the ac unit and the window. Make sure you have plenty of foam to insulate it.

I bought this to be able to support the weight of my new 8000 BTU window air conditioner without it putting too much stress on my new Hurricane window which is made of vinyl and very heavy glass. I also wanted a way to mount it without having to drill any holes in the windows which would void the warranty. A window support bracket seemed to be the best way to accomplish this. I read the various virtues of the different products in this price range on Amazon and decided on this one. I was surprised when I opened the box and discovered that Jeacent had changed the design a bit which made it much easier to configure and install. There are now push pins in the support legs that make it really easy to find the exact place to lock them in and once you found the right position for one leg, mark the opposite side and slide that support leg to it and you're done! They do recommend using the included Hitch Pins & Clips to lock the support legs in. I did this entirely from my open window and it took me less than 10 minutes. I did use a level to make sure it provided a downward tilt to allow the A/C unit to drain. Once I put the A/C in the window, it stayed in place placing no pressure on the bottom of the window nor on the sill below. To make sure the window could not be opened from the outside I measured from the top of the bottom window to the top of the window itself and then cut two pieces of 1/2" x 2" wood slats that tightly fit into that space.

This support bracket is not only very easy to install but because of the quality of construction, it truly does support my new window A/C unit without even coming close to "straining"!! I have absolutely NO DOUBT that it WOULD SUPPORT AN A/C UNIT 3+ THE WEIGHT OF MINE!!if you're looking for a support bracket that couldn't possibly be easier to install and IS STRONG!! THIS IS THE ONE TO BUY!! I can promise that you WILL NOT REGRET BUYING THIS A/C SUPPORT BRACKET!!Even if you have the old style "L" shaped bracelet that screws into the side of your place ONLY.You'll have a LOT MORE PEACE OF MIND BY REPLACING YOUR OLD "L" STYLE BRACE WITH THIS ONE!!The reader can easily see by looking at the photos. That it WILL ADJUST TO ANY SIZE A/C UNIT!!

If the window ac is 40kg or more then you need to bracket support

Very. Good

Buen producto, cumple perfecto con su funcionalidad

good product. Very sturdy

The best, easiest to use and install air conditioner bracket on the market. No drilling. Fits perfectly into Australian standard aluminum window rails or any window with a solid lip internally. Adjustable for most situations. Don't scrimp on a cheaper, difficult to use bracket. Spend the money on this and you'll never look back.