Dorman 697-500 Rear Differential Differential End Yoke Compatible with Select Models

When I was shopping for an end yoke for the FRONT differential of my 2002 Duramax 3500, I had a difficult time finding the right product. I relied on measurements instead of the manufacturer's listings. The manufacturer describes this part as a "Rear Differential End Yoke Compatible with Select Models," but it will work on the front differential of LB7 series Duramax models from 2001 to 2004.Here are the measurements I took:- Length (from outside ear to outside ear): 99 mm- Height (from the outside top to the outside bottom): 61 mm- Spline shaft opening: 58 mm across.- Metal bearing cover: inside 58 mm across, outside 92 mm across.The inside measurement of the metal ring cover, which protects the seals and bearings closest to the differential, is 58 mm across. This ring fits over the nub of the outside shaft of the spline. It's fine and fits. However, the outside measurement of this ring is approximately 92 mm. This discrepancy could cause issues and is one of the reasons it has been returned so much. IDKIf you still have your old yoke, you can use a bearing puller to remove and reuse the cover. The old cover measures approximately 86 mm across, which is just enough variance to create potential problems. Once I swapped out the new metal bearing cover with the old one, it mated to the differential housing as it is supposed to; it worked like a charm.Doorman has consistently produced high-quality products, and this yoke is no exception. I am writing this review to help clarify any confusion you might encounter when choosing a product for your needs. It would be helpful if the manufacturer included measurements in the product description.Hope this helps

Part G26060975 replaces the lousy seal that comes on this part. Pryed it off w a flathead, install took careful placement of metal & wood to press the new seal on

Working good now rust no leaks

Price was good and available. Less expensive than an OEM part plus it also came with a new seal which is not included from the dealer.I had the exact Dorman part on my truck for years and it would still be good if I didn't ruin it myself.

Dorman makes a solid product like this and the seller was great because it was so much less than the parts store. I try to shop locally as much as possible and I willing to pay some mark up but 100% is beyond what I consider reasonable.

First of all you need to know that the seal that comes with this kit is not standard oem size due to size of the yoke. The id of the seal is larger than standard for these model trucks. The yoke fits perfect on the pinion shaft. All that's is good. Now, i installed this on my 01 silverado in late april. Seal is now bad. Contacted Dorman and they told me they don't sell the seal separately. They did provide me the GM part number that you must use with this kit. The GM number is 26064028. It fits perfectly. This is the seal that you must use if this kit is installed. The standard oem size that would normally fit these trucks will NOT work with this kit.

This is a great kit. Third time doing the job (in dead of New England winter, burrr...); but after Dorman kit, it was the last time. Works great; no more leaks, small or big, anywhere. This a re-manufacture part, apparently with new yoke sleeve and associated seal. But its perfect! Note: an OEM seal won't apparently work should you want/need one, now or in the future (unless you can get one over-sized). However, this baby is set to go the distance and well beyond; great workmanship, all around! Before you do this job check the youtube videos on how to grease and seal parts for installation. I used RTV grey (highly recommended) and EP lithium grease (Castro blue is also a good choice). Oh yea, I have a RR 2 WHL Drive Suburban, 1996 vintage - still chugging.

Fit and easy to install. Like most parts it was a different style than the one I replaced, but I could appreciate the way the seal and flange seemed to be more protected. I'd be sure not to damge the seal itself because another brand might not fit with the flange. Thats just my opinion though.