MOKOSE Webcam Stand, Stands Bent 360 Degrees for Mounting on a Monitor or Laptop Mount with 1/4" Thread

You're good to order this now - super simple. Before i ordered this, I read the bad reviews and the middle reviews too, to see if there are any legitimate problems. But now after receiving this and then pairing it with a simple rotatable cell-phone tripod shoe-mount (purchased separately), I am glad I didn't keep looking for something else or something more complicated. The teeeeny tiniest issue is that the the bolt is a bit too short to easily get the screw-in to whatever you're screwing into to catch (because of the rubber washer thickness). But don't give up, you just have to keep it lined up and press (to compress the rubber washer enough), to get the threads to meet each other. A screwdriver helps. And the groove of the bolt-head is big and will work with any screwdriver. And unexpected bonus - the item is wide enough that it works as a desktop stand just as easily as on top of your monitor. Doesn't tip easily, even with a lightning cable plugged-in so you can keep charging while in-use.

I attached my Litra Glow to this for a monitor mount and it's great! The Litra doesn't come with a great mount if your monitor has a hump on the back (i.e. not super thin). This works well. The Litra is top heavy...so it'll tip over front-wise if you angle the light too far forward. Otherwise, it's perfect. Build quality is good, it's flexible, and a smart little design. Decent value for the money.

The default mount that comes with the Logitech Brio 4K webcam had a slight overlap with the viewable area of my monitor (HP x34) due to the thin bezel of the monitor. This mount was a perfect solution! The Brio's mount has ~12mm of overhang while this Mokose mount has ~7mm of overhang. This just clears my monitor's viewable area with ~0.5mm to spare. Very easy to install. The flexible "arm" is sufficiently rigid to hold in place on the monitor. I did add a small strip of double-sided foam tape at the very bottom of the arm to prevent any movement. The silicon surface of the arm doesn't offer much friction against the textured backside of my monitor. This wasn't inherently a problem, but I don't plan to move the mount around often (ever?). The screw mount "hump" could be a bit more adjustable. It's sufficient for my needs, but the range-of-motion is a bit limited and would be the only area I could suggest improving. Overall, super happy with this purchase. NOTE: if you have a Logitech Brio, the original mount actually pops off (give it a good tug or rock it laterally) to reveal a 1/4"-20 threaded insert that attaches to standard camera mounts (like this one).

Cannot hold the weight of a very light brio 4k camera and a ring knockoff light. Ring light has a thread that the webcam screws into and the ring light has a stand with a spot for a 1/4 thread where this mount went, and it just wouldn't support the weight, and the stand doesn't hold its shape. Was looking at other reviews that said to add tape and yeah, I can't do that with a $900 monitor since I just redid my setup to be a clean setup with no mess. The stand itself is not strong whatsoever and the screw goes all the way through when tightened all the way. It looked to be exactly what I needed but was just made too cheap for what I needed. Ended up needing a more expensive clamping stand for my desk after all. Too good to be true, and it was in my case. Returning first thing tomorrow.

Good product that works as intended, though priced a little high for what you get. I'm using this with a selfie light that has a 1/4" screw base. Since I wanted the light pointing slightly downward, the forward weight caused the mount to fail. I solved this by counterbalancing the back with binder clips. With the counterbalance, the mount works fine for my application. Pros: 360-degree flexibility, works with 1/4" thread accessories Cons: Overpriced, can't handle forward-tilting weight without counterbalance Works well but may need modification depending on your use case.

Does exactly what it's suppose to do. It's much firmer than the webcam stand that came with my webcam. Because of that it actually holds its position. Not sure why it's been so poorly rated here? It's the best option I could find online

Thought this was going to be the answer I needed for webcam on monitor mount. But it is weak to hold even a small cam and the bolt is pass-through so it doesn't hold tight enough to work. Find another instead.

Good product. A bit "light" for my purpose - I purchased it to use with my Logitech BRIO of the first generation, which is quite a heavy camera for this "light" mount, but somehow it could be fixed even with the Logitech BRIO; but with any lighter webcam it will certainly work perfect. The only thing I don't like is that you can't turn your camera lef-right when it is screwed to this mount the only flexibility allowed to move the camera up and down, meaning you will have to turn your notebook to achieve the right horizontal positioning. Otherwise, it is very good.

Leicht einsetzbar

I'm very satisfied with the customer service, thank you StarLineStore.

It’s what I wanted. Curved bendable soft mount with 1/4 inch screw on top. For monitor mounting.

Decent replacement for my misplaced attachment for the Logitech StreamCam

前提としてWebカメラに雲台が装着できるカメラしか取り付けできませんので注意が必要です。マウントは曲げやすく柔らかすぎずで自分の好きな位置に装着しやすいかと思います。カメラを固定する軸部分は若干緩いため、カメラを触ったりすると決めた位置からずれてしまうことはあるかなと思います。最近のWebカメラのマウントは割と調整しやすいものが多いと思いますので、紛失したなどのことがない限り交換用途では不要だと思います。