2-1/2" x 10' Ultra Flex Clear-Vue Heavy Duty PVC Hose Made In USA

It's pretty hard to get excited over a hose but this is' a very nice hose been using for years....getting bact to the 10 ft and do meen 10 ft ..stretched to the MAX...hose relaxed probably more like 6-7 ft..worth the money just order 20 feet and not place two 10 ft orders like i did... you get a hose that will last a lifetime ....perfessional installer for 17 years love this hose. stays clean, very flexible, perfert........

I just got it. Screwed both ends that I received at the same time and connected one end to a Fein Turbo II vac. I turned the vac on then put my hand over the other end. The hose sucks together until the wire coils are as tight against one another possible but the diameter is not reduced at all. It of course does not collapse as long as one end is not completely sealed off. The hose is much more flexible than shop vac hose I've had for some years. I would buy more without reservation if I need it.

I bought this to replace the crap hose that came with my ShopVac. Even though the ShopVac hose is listed as 2 1/2", it is not. The OD of the fittings are 2 1/2" but the OD of the hose is 2 1/4". Nice going, ShopVac.This hose is 2 1/2" and therefore is too big to use as a replacement. Too bad, because it's clear so you can see if it's clogged, and it's wire reinforced so it won't kink, unlike the garbage ShopVac hose. Had to return, although no fault of this hose or its manufacturer.

The last year I've been adding on to my dust collection system and there always seems to be a need for more hose. Though I think I am finally set up with everything. (fingers crossed)I have a 2" PVC system, powered by a bigger shop vac. This hose it just as durable as any of the others I have. It's study with a tough wire core. Takes some muscle to cut the wire in the hose, but I think that's a good thing, as it makes for a stiff, durable hose.Don't know what else to say, it's a simple product that works as it's suppose to.Was a good purchase, I would buy again with out hesitation.

I used 2 short pieces of this hose to replace the decayed factory AC/heater duct hose in the dash of my 1978 jeep wagoneer.It's 2.5" ID slides over the inlet and outlet pieces in the dash snugly, I used 4 2.75 " diameter radiator hose clamps to make sure they stay in place rather than tape like the factory hose was attached with.I haven't looked at the duct hoses on my 1990 wagoneer yet, but I'm hoping the ducts are the same size.All around a good, well made product that saved me a lot of time and money

I've been using this product for over a year now. It has held up very well on my shop vac even when using it to suck up off my grinder with Sparks flying through it it has held up perfectly.

This isn't a perfect fit over the port for my compound mitre saw but it is close enough when used with either a clamp or a tapped hole on the saw with screw and washer. The clear plastic makes it easy to ensure that the sawdust is going into the hose (and not clogged somewhere in the saw!).This is also good for smaller jointers, stationary sanders, etc, that use this approximate size.

Real nice flexible hose used it for dust collection to my 13 in planer .hooked it up to my 4inch hose 2 hp dust collector.I can close the blast gate and it won’t crush the 2 1/2 inch so it is pretty strong too.It’s really clear so you can see the chips going through.

Muy buena calidad y muy buen precio

Have bought a few of these now, they are pretty rugged and bounce back if you step on it... once or twice but wouldn't stand up to regular abuse. I have a couple suspended and don't show signs of wear but stay in the extended position unless under vacuum.

Quality materials

Buena Calidad !

I have bought other brand hoses for a less money but they don’t fit dust fittings well and tend to want to stubbornly contract back to their original shipped length which is super annoying. This brand, on the other hand, is both flexible and does not want to forcefully contract back to its original state. Will buy again.