Portable Dual Laptop Stand - Standing Table with Adjustable Height, Ergonomic Design & Anti-Slip Prongs for DJ Mixer, Sound Equipment, Workstation, Gaming & Home Use - PLPTS38, Black

This stand works well so far. It holds my MacBook and Pioneer DJ DDJ-FLX4 with no problem, which is what I bought it for. As for assembly, it was a little tricky to put together by myself—not because it's complicated, but an extra pair of hands would have helped. Once assembled, it's good overall, but it doesn't feel as sturdy as I expected. It gives the impression that one wrong move could cause it to topple over, though I’m hoping that won’t happen. I’ll update if it does, but for now, I’ll give it the stars I think it deserves based on my current experience.

None of the other stands really offered what I was looking for, but like other people have said after reading the reviews I was hesitant because of the mentioned flimsiness and overall stability. When I first unpackaged it I was a little bit overwhelmed, because it wasn't obvious at first how it went together. After thinking about it for a minute and looking over, it really couldn't be easier. I feel like anything easier would be flimsy, and as long as everything is tightened well, which means checking all of the multiple pieces that unscrew, it should be plenty sturdy for you. As far as it being stable, just make sure everything's tightened down. Now I have done two mods to mine, which took no tools other than a pair of pliers. The first one I did was sometimes I like it really low, so in one of the photos you'll notice at one of the outside brackets has a little piece broken off the bottom of it, that's so I can lower it down all the way. I just took a pair of pliers and folded it back and forth until it weak into the metal and snapped off about a half an inch of metal. That's the caveman way of doing it, anything else would do better but I still got it done. The other mod I did which has worked for me pretty good in the last couple of months is to prevent the stand from tipping backwards which it might do if you have a lot of weight on the top and a light controller like I do, on the bottom. So I just moved up where you screw the stand in at. I'm only using one of the two holes, but I've got industrial double-sided tape other under the other end, which is just there to prevent it from sliding, ideally you would want to drill out a hole in either use a flat bolt and washer, or use the flat screw that came with it in and tap a new hole so you can screw in that front screw.. it's still super sturdy, as you can see right now it's loaded up and balancing on a bed, which it could not do prior to me repositioning the legs. They could be part of the reason why I think it's so sturdy . I usually have my controller and my laptop pretty flush, but I decided to raise it up just the middle platform recently to try to help my posture while playing at home. It's a great value for the money, and really nothing else I or other have seen has this form factor. And while adjusting the height on this isn't as fast as a push button clamp (what's used on aluminum crutches) I think this is far sturdier than that, and really not that bad to take apart and re-assemble, I wasn't looking forward to it until I did it a couple of times, not an issue at all. Height is sufficient enough to where you can even put a keyboard or some performance pads on the bottom if you're using on a desk. If I could go back I would purchase again without question.

IT gets the job done if you don't mind that it is time consuming to alter its size and that it is not very robust. If I was using it professionally and could afford it, I would buy something more professional grade. I put a Yamaha MG 10 un a table below it with a laptop on top. Good enough for my little home studio.

As a DJ, gear that’s portable, sturdy, and functional is a must—and the Pyle Portable Dual Laptop Stand delivers on all fronts. I use it for gigs, practice sessions, and even in the studio, and it’s quickly become one of my most reliable pieces of kit. The dual-tier design is perfect for holding my laptop on top while keeping my controller, mixer, or secondary laptop right below. The adjustable height and angles make it easy to customize for any setup, whether I’m standing during a set or sitting while producing. The ergonomic design really helps reduce strain and keeps everything right where I need it. Build quality is excellent—the stand feels rock solid with no wobble, even when I’m typing on my laptop or cueing tracks mid-set. It folds down compactly, making it easy to pack up with the rest of my gear, and setup at venues is quick and hassle-free. What I love most is that it gives me a professional look on stage—organized, elevated, and clean. No more awkwardly stacking gear on crates or tables. For DJs, producers, or even live streamers, this stand is a game-changer. Highly recommend it for anyone serious about keeping their setup both practical and professional.

June 2025 at $41 USD. This is *not* a $40 stand. This is a $10 stand. Two screws sheared off when hand tightening. Obviously poor quality Chinalloy.metal. I have a workshop and found proper steel screws to repair. I had to reverse the stems of the screws which sheared to clear the holes. That was absolutely a $10 stand issue. I have a Korg MS2000 on it. 7.1kg/15.6 lbs. That is almost exactly HALF of the max weight they claim. The thing leans forward and wobbles like you wouldn't believe. The back is about 1cm off the desk. I might try to screw it into the desk or try the photography sandbags someone else mentioned, if they are small enough. If I hold the back down, it wobbles 95% less. So, that is going to be important to remedy. Again, a $10 USD stand issue. The tray adjustment screws are welded into the lower brackets, then the adjustable pieces slide in a slot over those, with tiny wing nuts hold it. I am scared to detach of tightening those down hard, now. With the base feet bending into a curve under the strain, I cannot trust any of this metal. I am not going to count this against them, but wanted to mention in case others were wondering. If you would like to flip those upper brackets to get another synth above this, it's not going to work unless you keep this very short. You need to think about the fact that you only get three bars to deal with. I have the front of the Korg about 10 inches off the table, but that took using the last two holes available. The only bar left over had to go up high on the top hole. That means there would only be one bar to hold those... not going to work. MAYbe if you dropped everything down, so that you could get two bars holding that upper portion... maybe. Also, you need to remember that those upper bracket will put a limit to your depth on the back side. If you install them, nothing will go back past them. Also, using the top two available holes, the bars cannot be tightened enough to keep the slop in the holes from allowing it to lean forward slightly. I might drill one more hole on each side to give it three points of holding, which would stabilize that. Another $10 stand issue. One thing they do not make obvious is that you get those 3 cross bars in 5 sections. The middle is the longest, then two shorter sections on each side of that. They all screw into each other. This is what gives you width adjustment for the upper platform. You have two choices - between first shorter pieces or second shorter pieces. That's it. I erroneously assumed those could slide. Now, looking very closely at the main photo, I see the sections. That was not obvious to me, so hope it helps someone. EDIT: I have resolved the forward tilting issue by instead using a couple of small C-clamps holding the back feet down to the desk. No sandbags or screws required.

I have owned so many keyboard/synth/equipment stands over the years and rarely do they last or measure up. But this stand is a more solid solution than anything else I have tried. It is rugged, made from quality materials and has the workmanship of a product made by a company who actually cares what their customers think of them, and would like to do business again in the future with them. The rack's arrangements are flexible in adusting heights, and provide such a solid base that I won't worry about my equipment now. It's construction is really ingenious and self reinforcing. The metal is nice and thick and has a very "finished" and professional look to it. They even included adhesive cushion pads to protect furniture surfaces and the equipment that I will be placing on it from scratches and dings. Very nice touch !!! I can't wait to look over the rest of their products and start getting excellent quality equipment at such a tremendous value and price.

1. This product was perfect to raise my controller and laptop to a level that relieved a lot of the strain that comes from looking down at controllers/any gadget for long periods of time. This, alone, makes it a worthwhile product. 2. Assembly could have been easier. Can we get a "pop and lock" version 3. This product is sturdy and does hold the weight as described. I used the box underneath for extra security. If you have something like a Rev-7, you might have to put brackets on the bottom to keep it from tipping over etc. 4. Portability? Yes if you have a very light weight controller. I won't take it with me. I wish I could, but I would have to take a brace and lock it down etc. More work. 5. SUGGESTION: Make a popnlock version that will hold up to 75 lbs and we all win. This is great for at home.

I am a professional podcaster, and I've purchased many Pyle products over the years because they have reasonable quality audio equipment at a very good price. Though this device is marketed as a dual laptop stand, I use it in my studio to mount my audio mixer and a MIDI controller. It works fine for that purpose. I purchased it under $34, and at this price point, I do not feel like I've gotten a bad deal. But, this device, though it stands squarely on my desk and does not wobble in the uneven stance sense of that word, shakes when ever I touch a key on the MIDI controller or adjust the knobs on my audio mixer. It also lacks any support between the bars. So if you place anything on this which is not wider than those support beams, it just falls right through. That, I think, is kind of silly. Would a single plank across the platform have been too much to ask? Well, I didn't ask. I saw what it was and I bought it anyway. I should not complain too much about that portion of the design. But, you should keep it in mind for your purchase. You can also forget about this thing being portable. I do not think it is designed for that purpose, but Amazon asked me to rate that portion of it so I will comment upon this. The device is way too large to be carrying around full assembled. It is easy enough to assemble/disassemble, it takes a few minutes. But it is basically a bunch of metal bars and screws, and I wouldn't want to take this on the road with me. I regularly travel with an alternative set of studio equipment. Frequently, I purchase a cheap product, and after seeing what it lacks that the higher priced product provides, I buy the higher priced product and downgrade the lower priced product to my travel gear. That will not be happening with this device. While one could theoretically take it apart, put the pieces in a bag, and take it with them, it would be supremely impractical, and too much hassle to do in each hotel I went to when there are better products suited to that purpose. This will remain where it is until I replace it, and then I will throw it in the recycle can.

Parfait !! Comme sur l'image. S'ajuste à la perfection avec mon Akai APC40 et mon ordinateur portable

I use this for two mini synths, and it's perfect for the job.. its sturdy, so I can play them, doesn't shake or rock.. the assembly was very easy.. took 7 mins.. awesome product. It's perfect for dj table or synths..

Prima standaard voor laptop en flx4 alleen niet makkelijk even snel uit en in elkaar te zetten dus voor een drive inn show niet echt handig

Good quality and sturdy, one of the best buys in Amazon. Highly recommend it. This hold my DDJ FLEX 4 and if we'll placed, leaves room to hang the headset.

Thank you amazon for huge discount price. I got it for only 87dhm and it really handle very well my 2.5kg Panasonic Toughbook with Hercules Inpulse 300. It wiggles a bit but it doesn't bother me as long as it keeps organize my equipment.