Zeelo3D Printer Upgrade Extruder Dual Driver Long-Distance Remote Metal Extruder Right Hand Block Kit Spare Parts 1.75mm Filament for CR-10S Pro Anet A8 Anycub Mega Wanhao i3

Nice upgrade over the standard one. Works well and easy to install.

This extruder pulls the filament thru without crushing, or deforming it. Easy to install by watching the video on the site. You MUST REDO your esteps for this product. My Stock estep was 94, but with this one it's 135. The dual gears are smaller in diameter, so more turns are needed for same length of filament. There are many videos on youtube on how to do this. Easy install and calibration.

It requires a little thinking at installation, it's not very user-friendly. However, the product is made from quality material and seems to be sturdy. Hopefully, it'll last a long time. Good value for money spent.

Well so far it is working very well. It pulls really good with no slipping so far. There is no instructions which always makes me mad. I can assemble about anything but I know some people cannot. One warning on the gear assembly that is ready to go do not over tighten the bolt or you will lock the gear up. The gear that goes on the stepper shaft should have two set screws instead of one. You will have to make sure the gear on the stepper motor aligns at the same height as the other one or it may not pull right. This is worth the money because if you get a roll of pla that has the diameter too small this will make up for it.

Could not figure out why after dozens of good prints, they all started to fail 1/2 way thru. Found out thru a youtube video that the plastic tensioner supplied with the printer is prone to fail and crack where you can't see unless you remove it. Same identical crack, same location. Researched aluminum tensioners and upgraded to the duel tensioner! Everything is back to normal. During installation of the new aluminum tensioner you should pack the bearing with grease to extend the life of the unit!

It's very good quality and easy to install without instructions. All the people who said it was difficult to install are crazy and obviously have no sense of everyday know-how. Buy now.... Like go and click the buy button... Just tap it now.... BUY IT!!

Product was good but was sent wrong fitting for the filament. Still haven't put on my printer, had to order other fitting.

I bought this metal extruder when my original plastic one failed me and broke.I had to go find a YouTube video to show me how to install this, but with that it was easy and quick.Once it was installed it fixed my problem I was having with 3D printing.Would recommend to anyone with a plastic extruder to upgrade to a metal one and this one is great - especially for the price.I have a Voxelab printer.

A bit confusing to install and calibrate, but once finished it seems to have greatly improved print quality. Is also easier to change filament now than with the stock Ender 3 extruder.

Installé. Fonctionne bien

J'ai un creality ender 3 PRO, et le moteur de base a la tige de l'axe E trop courte, moi j'ai acheté ce modèle.Creality Moteur pas à pas officiel 42-34 (Z), imprimante 3D CR-10 X-Z Moteur pas à pas 2 phases 1 A 1,8 degrés 0,4 N.M, compatible avec CR-10 Series Ender-5 et Ender-3 Series Z-axis (que vous pouvez acheté sur Amazon.ca) Cette extrudeuse double fonctionne à merveille!!!

This replaced another aluminum extruder I had as I wanted Dual feed gears.For the Ender 3V2, you need to know two things:1) the feed is 5mm higher than the standard, so if you have something like a filament sensor before your extruder and it's lined up, you need to redesign.2) the steps/mm needs to be changed from whatever you are at to about 140.Otherwise, I'm thrilled.

Very strong stable and dependable extruder. Some notes: Black powder residue eventually shows up after a while of printing and probably comes from extruder gear grease probably not something to be worried about. Filament residue eventually piles up at the filament inlet as it scrapes during printing due to extrusion and retraction.