Deep Pour Epoxy Resin Kit 3 Quart - Food Safe, Clear Casting, Ideal for River Tables, Artistic Castings and DIY Projects - High-Gloss Finish, Up to 4" Pouring Depth - USA-Made, Low Odor

I used this for an epoxy river table. It worked great, was crystal clear, and dried hard. A few tips:-This is very thin - it flows like water. If you have any leaks, it may all leak out. I did an initial pour of a small amount and tilted the table so it flowed into all corners and cracks. I let it cure for ~18 hours to partially harden and seal any leaks. Then I poured the rest.-Make sure your table is exactly leveled. This epoxy will level itself fairly perfectly, so any tilt in the table will result in unevenness in the thickness of the epoxy.-This takes a couple of days to "harden". It may be unnecessary, but I gave mine a week before putting it into use. If you are uncertain, save some epoxy in the pot you mixed it in and test its hardness by pushing a fingernail into it.-If you want swirls in tinted epoxy, it needs to be done when the epoxy gels. At the temperature I was working at, it took about 12 hours. I used mica-based tint, and it seemed to settle just a bit. So when I gently stirred the epoxy, it came out with nice swirl patterns. You must do this very slowly or you risk getting bubbles that will not come out. Definitely test on a scrap piece to see how long you need to wait, and how gently you need to swirl. Keep checking on it (and maybe re-mixing) every half hour since the swirl pattern can start to settle out even when the epoxy is gelled. You can also try mixing in another color, but I haven't tried this yet.-be careful of dust. This product is so mirror smooth, any dust landing on sticky epoxy can be visible in the finished product.

This stuff is fantastic. Super long cure time gives any bubbles time to rise out.You do need to think about how you want to do colorants as they can settle during the long cure. Most of the time this stuff doesn't start to gel for 12 to 16 hours. But it can pour deep, and very clear.Cures rock hard after 36 to 48 hours. Resist the urge to mess with it late in the cure, it may not be as hard as you think just yet. Just leave it for several days, it'll get there.

I have been using this stuff before it was available on Amazon. It is a great product and a perfect resin for deep slab river tables etc. It is very slow cure so it doesn’t heat up and bubble or crack etc. above is a 13’ bar top I just sanded that I poured over 7 gallons into. It was a 1-3/4” deep pour. Beautiful stuff. Easy 2:1 ratio mix. As long as you take your time and have the correct temps recommend it works great. I have used other higher priced competitors 3:1 mix slow cure resin and it’s just as good and much more economical.

The media could not be loaded. I ordered this to make live edge cutting (Charcuterie ) boards. I’m not a wood worker, so Its just learning for me. I ordered this based on reviews and price point.First, it pours just fine. I didnt use a funnel or anything other than 1000ml plastic cups. They have measurements on them. Second it mixed well with a silicone paddle. I was able to make three boards with this, although i did over mix on each of them. I covered the entire surface of my wood each time.This mixed well with the pigments I purchased with a few questions. I have not dialed in the right time frame to get the right swirl pattern. One session settled quickly. This seem to cure the best around 70-71 degrees. However it took a full 48 hours to harden and most I let sit for 72 or more before finishing. They polish well to 2000 grit, and upot further inspection I believe I should have sanded and buffed more.These did not surface well through the planer we used. Believe me when I saw this is a professional quality 20” carbide tipped planer. We instead built a router jig and that did the trick.Overall I am pleased. Check the photos for the output.

I as a creator is still learning. But this Resin really did help put me in the right direction. I have been making DND dice for my brother and the Resin I was using was just full of bubbles no matter what I did. I got this resin and very little bubbles are in the dice. Still working on making it no bubbles. But this definitely will help that!

I needed it to thicken up to work worth it easier, but it's nearly impossible to get this to thicken up. I tried letting us sit for over an hour, I've tried adding baby powder, I've tried adding heat... still really liquidy. My practice peices turned out pretty nice, but for something that was maybe ¼" thick I had to let it sit for 2 days before I could take out of the mold & it was still a little bendy. I do not plan on buying this again, it just doesn't do what I'm looking for...Shipping was fast & products arrived well packaged.

Used this product to make the water feature portion of a board-game. I have never used a casting resin before but the directions were clear and simple. The only issue that I ran into is that when I used a second pigment, that color sank to the bottom over time and the blue in the picture is all the remained. Other than that, everything was perfect. Would recommend.