SINGER® 4423 (Grey) High Speed Heavy Duty Sewing Machine with Accessory Kit

Sure the outside is mostly plastic but then that's how stuff is made these days. But underneath that plastic is a nice metal frame. It is a sturdy unit. I've had my 4423 for a month now and I'm completely happy with it. I also have a 1938 Singer model 221 that I love but it is a straight stitch only machine and doesn't have a free arm feature. The 221 has a little more power than the 4423 but for a modern machine it would be tough to find a better one for this price, with all the stitch features and button holer. After much research I think that the people that report sewing problems with this machine may be using the wrong bobbin. Only use the type 15 plastic bobbin. Metal bobbins may cause early bobbin case failure and 15 J will sooner or later cause a massive jam-up or incomplete stitches. Read the owner manual, watch the videos on YouTube if you have problems, maybe even before you get the machine. There is a lot of good info out there that will help you avoid trouble. The needle threader works very nicely and I really appreciate that since my near vision isn't so good anymore. The bobbin winder works well and threading the the bobbin is a snap, see the drawing in the user guide. It will sew with a double needle too but it works best if you don't run the second thread thru the thread guide just above the needle. Yes the feed dogs don't raise immediately when you move the switch back to normal but as soon as the machine completes one stitch cycle the dogs pop right up and feed normally. It's not a problem, just the way it is. People have complained about the built in light, I don't know about how it was but the new machines have an led lamp and it is bright enough to sew in a darkened room. Yes the wire to the foot pedal is too short but now I can splice in an extra couple feet of wire to lengthen it. The foot pedal is very controllable and the machine WILL start and run slowly. I sew in stocking feet or barefoot, always have. I have better control that way. The 4423 has replaced my model 1937 Kenmore portable which was a free arm zig zag machine. The 4423 is more powerful than that Kenmore although it is not much smaller but it is much, much lighter. I was tired of dragging that old boat anchor around and that was the primary reason for buying the Singer. I think it is quieter than the Kenmore too. I had considered a fancier electronic machine but I've been in electronics repair for a long time and finally decided that it would be a bad choice. Nothing like a nice LCD panel to tell you what you should already know. Expensive electronic equipment will break down for the dumbest of reasons so it stands to reason that cheap electronics wouldn't be any better. Not to mention the repair costs, if even possible. So a nice mechanical machine was my choice and I really like this little Singer. My sewing these days is mainly repairs and mods. I don't know if mine will sew leather or multiple plies of denim and it doesn't concern me much cuz it does what I need it to do very well. Oh, by the way, all the important accessories are in the "secret compartment" in the removable free arm piece. And the "cover" is a just crappy piece of gray paper in a plastic bag. I cover mine with an old T shirt, it works just fine and actually looks better than the included cover.

I was hesitant to leave a review, as I'm so woefully ignorant of the sewing arts and the black magics of how sewing machines work; but then I thought my inexperience might help others out, so here goes. Despite having a family who sewed, and many friends who made costumes for Ren Faire and comic/ gaming conventions, no amount of begging or pleading has ever gotten one of these lousy #%&!'s to teach me how to use a sewing machine. However, as is wont from time to time (and especially for one who engages in crafting of all sorts), I have found myself in need of joining two pieces of fabric together, preferably in a manner that doesn't look like a sugar-high child with a glue-stick did the affixing. Therefore, at three different times in my life, I've determined to learn how to operate one of these machines, or die trying (or, well... go naked trying!) First was a cheap Singer I bought new some 20-years ago. I don't recall much about it, or the model number... again, 20 years ago... except that I could never get it to work. And by "work" I mean I never managed to even get a straight stitch on scrap fabric. The machine was fine, as a friend made a gloriously beautiful cloak on it for me, but I couldn't get the hang of it. The second time was two years ago, when I borrowed another friend's Bernini that was so old, the user's manual read like those "Good Housekeeping" articles we all laugh and make fun of now, complete with women wearing pearls and heels while sewing. That time I managed to complete a couple of small projects, though not very cleanly and not without breaking dozens of needles. Third time's a charm! I bought this Singer 4423 because, once again, I found myself needing to merge nylon straps together, and there was no other option. So emboldened by my success with the old Bernini, I took the plunge... and am really glad I did! Again, I must warn you, I'm not doing anything fancy, so far just straight stitching straps together... but this machine has been a breeze to set up and operate. The quick start guide had me spooled up and sewing within minutes of taking it out of the box. Threading the machine is incredibly easy for idiots like me because each step is numbered ON THE MACHINE!!! Never once had to refer back to the owner's manual when changing thread! Three tries on some tiny nylon straps to figure out where my tension needed to be set, and I was off and running after that. If people didn't know any better, it actually looked like I knew what I was doing! The one common complaint that had me worried before ordering was that people complained that the pedal was too sensitive. Well, again, I've only ever used two machines other than this one, but the pedal sensitivity and speed on the 4423 is no different than either of those older machines. I don't think anybody who learned on an older machine will have any problems here. (Am I saying that if I can modulate speed just fine, then others can too? Yes, yes I am). I am pleased with this machine. Very idiot-proof, durable enough that I spent today sewing strap after strap, and never once broke a needle or snapped a thread. Did what I asked of it, and now I'm more confident in seeing what else I can learn and get it to do.

So far so good with this Singer HD sewing machine. I am very pleased with how well it sews through several layers of fabric, and how easy it is to fill the bobbin, change the presser feet, etc. The lovely light blue color makes it pleasant to see sitting in the room. I had no need for a $15,000 embroidery machine with computer, and this Singer does everything I need and does it well.

Needed to sew some clear vinyl to my boat enclosure. Went thru the canvas-1 layer of 20 gauge and 1 layer of 40 gauge clear vinyl all at the same time-Broke 5 18 size needles but did entire enclosure. Trick is be sure needle is always in up position when stating to sew as it needs force and torque to go thru such heavy materials. adjusted thread tension to 3 thread length to 3 setting. used V89 poly bonded thread. Don't pull material too fast when sewing and try to keep pedal at a good speed after it starts. If pull too fast or thread tension too hi will tight will break needle or thread, Had problems when machine speed too slow. Thread broke many times-there is a learning curve yet for this price as compared to a much higher priced machine it is worth the learning curve. Sewed a ripped leather wallet no problems. I thought it was a great value for the price. Did not have to use walking foot adapter I bought. My 14yr old son sewed and I helped pull the material thru as it sewed. Prob sewed close to 200 linear feet straight stitch. No problems at all going thru canvas and 40 gauge clear vinyl (eisenglass) mainly had a few difficulties (learning curve) going thru a 3rd 20 gauge eisenglass all at the same time. Cut out old clear vinyl but some pieces did not want to spend time de-threading to remove last 1/2 of old clear vinyl so just sewed on top of it. No problem sewing zippers. I had to place a few weights behind machine as when pulling long pieces of material thru it the machine started to move backwards. I looked at Sailrite new machines and used upholstery specific machines on craigslist and ebay but took a chance with this very economically priced one and though had some initial problems (mostly learning curve) it did the job going thru some heavy material, Watch some Youtube videos before starting. Spent about 15 min practicing on small pieces As far as professional looking results for a beginner sewing canvas materials it was probably not designed to sew thru and for someone who has never sewed I got a 6.5 to 7 out of 10 and was well pleased. I bought off brand 18 needles (cheaper) and they did not hold up to the singer brand needles, (should have listened to sewing lady at Hobby Lobby). As thread broke and had to replace needles from time to time and listen to my son use curse words he should not have known-he finally learned patience and could rewind a bobbin, attach a new needle and thread a new needle blind folded at amazing speed. Told him he must have Korean blood in him.

Works well when sewing jeans, easy to use, seems durable for plastic exterior, mechanically sound, seems to be good quality.

There are a lot of reviews here of people frustrated with the Singer 4423. I was going to purchase this machine back in November, as I needed a machine to handle automotive upholstery and other heavy fabrics. I hesitated on buying because of less then stellar reviews. An Amazon lightening deal changed my mind, as the price was under $100. I received my item well packaged and expediently (thanks Amazon). The directions that come with it are not great, but get the basics covered. I utilized the internet for more detailed instruction, and well as for video guidance. After using the sewing machine for several hours, I too became frustrated. So much so, that I initiated a return. It seems I could not get the thread tension correct, and I would end up with tons of bobbin jams. Nobody wants their bobbin in a jam. After sleeping on it (not literally), I researched more on the internet. I found a few tips that not only helped, my project turned out great and I was able to use the 4423 effectively. My Tips: 1. Use the felt bobbin spacer if the bobbin is racking in the bobbin case. 2. Important. Use only the plastic - not metal - bobbins. 3. Make sure you thread correctly. Thread tension is critical and is managed at loops #3, #4, and #5. When threading, be sure to give a slight tug to ensure the thread has seated into the blind tensioner. Also don't forget to run the thread behind the guide #6. 4. This might seem obvious, but be sure to drop the presser foot. It's easy to forget especially when setting up thicker fabrics/upholstery. If you forget, you'll know soon enough, by having a mess under the fabric on the bobbin side. 5. Practice with the foot control. It launches from 0 to 60 in a split second. I'd like to find a way of better control here, as fine control is challenging. 6. Use the correct needle size. Mine shipped with a 90/14 which is good for many things, but I recommend a 100 for thicker stuff, like chihuahuas and small pets. Just kidding about that small pet crack. I gave this machine 5 stars solely because for the money (<$100), it was a no-brainer. I'd give it 4 stars if priced in the usual $125- $150 range. It's not perfect, as the foot control is too sensitive (like my wife). But it is a well made piece of equipment that CAN handle heavy fabrics. It went through 6 layers of vinyl upholstery as well as plastic piping, without struggle. I did find that best results were obtained when the needle is started manually in the thicker, multi-layered fabrics. Stitch patterns seemed to work okay, but I only did some messing around with them, just to see if they worked. I really only used the straight, and zig-zag with frequency. One other thing, the machine is light, which is good and bad. Good, as it's easy to transport, but bad as it will move when pushing heavy stock through it. Use a rubber mat, or better yet an appropriate table.

Great. Basic, strong, keeps working. Powerful. But no seam guide! Get the magnetic one.

This was my go-to workhorse for 25 years, now they are garbage. I have been extremely loyal to Singer, and these machines in particular. I sew professionally for my business. I have been using the Singer Heavy Duty machines since the beginning. I appreciated the speed and simplicity of these machines. I only use these machines for straight stitching with a twin needle. I know how to trouble shoot problems when they occur. I'm a pro, especially on these machines. I use these machines for about 10 hours per week. That isn't excessive. I properly oil and clean them, replace needles often, know how to spot a bad bobbin or bobin casing, use high quality thread, and fully understand how to adjust tension. I am a master at using twin needles. These machines would usually last me about a year, then when they start giving me problems, I simply donated and replaced them. They aren't expensive, so it is more cost effective to replace them than service them. I loved their SPEED. They are fast. But after a week, they are noisey. I can deal with that. I have already purchased two Singer Heavy Duty machines in the last 2 months. The first one was garbage. It constantly gave me problems, so I quickly returned it and bought another. The second machine is no better, it is also garbage. Thread constantly breaks and nests under the fabric, and needles keep breaking. These are the exact same problems I had with the machine I just returned. Experienced sewists may say, "Hey, you're using twin needles! That's the problem! They are always problematic". I'll respond by saying I have been doing this for 25 years on these machines with minimal issues. SOMETHING HAS CHANGED. Having one bad machine could have been a fluke. Two in a row in less than two months? That's a sign that Singer QUALITY has drastically gone downhill. Yesterday, I finally got to the point where I couldn't do ANYTHING with this machine. I changed the bobin casing, needle, and carefully wound a new bobbin with NEW thread. There was no dust, lint, or loose threads in the machine. The needle wasn't bent or dull. I could find absolutely no reason for the problems I was having... the same as with the last machine. These machines simply don't seem to have the quality that the prior Singer Heavy Duty machines had. I can't afford down-time, and I wasted the entire day trying to sort this issue out, without success. So I decided to just switch to a different brand and had a new machine delivered today so I can get back to work. I'm not leaving this comment to plug another brand. I'm just trying to show how frustrated I am that the quality of the machines has degreaded so much over the last year. After some research I decided on a Necchi machine. I wanted to keep the cost down because I do consider these types of machines to be semi-disposable after a year or so, and I wanted the same sewing speed. It arrived today and it works PERFECTLY on a straight stitch with a twin needle. I used it for two hours without the slightest hiccup. I am also AMAZED at how much quieter it is than the Singers! To compare the noise difference, the Singer is a baby crying in the middle of the night and waking me up from a deep slumber, while the Necchi is like a baby cooing in the middle of the afternoon. The Necchi isn't quite as fast as the Singer although the both claim 1100 spm. Only time will tell how well it holds up. But, so far I'm pleased. In a nutshell, these Singer Heavy Duty machines are not your "granny's Singers". Singer was always my go-to choice, but now they have serious quality control issues. I'm not sure I could go back to Singer again.

ÜRÜNDE SIKINTI PROBLEM YOK KARGO İNANILMAZ HIZLI 3 GÜNDE İTALYADAN ELİME ULAŞTI GAYET BAŞARILI TEK PROBLEM KARGO KUTUSU ZAYIF YAPILMIŞ AYRICA KULLANMA KLAVUZU SADECE FARKLI DİL BİR DE ÜRÜN SESİ FAZLA AMA AMAZONA ÇOK TEŞEKKÜR EDERİM SATICIYADA

AMO esta máquina de coser. Es mi primera máquina y cubre perfecto mis necesidades. Además el color es hermoso. Ya he hecho varias cositas, principalmente arreglar ropa que me queda a muy grande.

Après avoir lu les commentaires sur la Singer 4423, mes attentes étaient hautes.. et bien après l'avoir essayé, c'est encore mieux que ce que je pensais! Ceci étant dit, ce n'est que la troisième machine à coudre que j'utilise et je suis loin d'être un grand couturier! Je me contente de faire mes bas de pantalons, réparer la fourche de mon linge de travail ou encore mettre des "patchs" aux genoux des pantalons de mon petit garçon. Donc avec ceci en tête, je trouve que l'enfilage de la machine est extrêmement facile, des numéros sont inscrits avec des flèches pour nous indiquer ou passer le fil et l’enfileur pour l'aiguille fonctionne très bien! De plus on voit que la bobine de fil est à l'horizontale sur le dessus de la machine, mais il y a aussi un adaptateur qui permet d'en mettre une autre à la verticale un peu plus à droite. Je suis capable d'utiliser une plus grosse bobine conique (une pour surjeteuse) dans l’emplacement horizontal et ça fonctionne quand même bien. Une autre particularité super utile de cette machine est le genre de base/tiroir qu’on peut retirer afin d’avoir un plateau étroit permettant d’insérer une manche de chandail ou un petit pantalon d’enfant par exemple. Ça s’enlève et se remet super facilement et ça permet de faire des coutures à des endroits que je ne pouvais tout simplement pas avant. La machine de façon générale est surprenament légère même si le cadre intérieur est en métal. Finalement j’ai découvert qu’il y a une application disponible pour appareils mobiles; c’est 100 fois mieux que la belle-mère!! 😊 Il y a toutes les instructions de base pour la machine, mais aussi une section où l’on sélectionne le type de tissu qu’on veut coudre, le type de couture désirée et l’application nous dit quels sont les accessoires et réglages requis pour y arriver! On y voit même un petit vidéo nous montrant comment faire.. Donc pour les gens peu expérimentés comme moi, c’est super utile! Pour les moins, le levier du pied est en plastique, je ne vois pas « sous le capot », mais je suppose que c’est le cas pour d’autres pièces aussi; on verra sur le long terme si c’est durable. Donc en résumé je suis très satisfait de la facilité, versatilité et puissance de cette machine et la recommande sans hésitation!

It had the wrong plug for Australian outlets, so I had to send it back, thank you

صعبة جدا لازم يستخدمها شخص خبير جدا وتركيب المكوك متعب جدا قديمك نديمك