Front Splitter PRO – Fit 2-inch Lip Spoiler Protect and Customize

I never care to leave reviews, I saw this product, decent price and seemed like the reviews were okay, so I gave it a shot. I kind of figured it wouldn’t work out and I was just going to return it. It got here in one day, that alone was nice but that was more Amazon’s doing then the product, but I opened up the package, grabbed some scissors and ran outside to put it on, please note that it had just rained that day so my car was wet and muddy. I peeled the tape off and stuck it on, be careful as to stick it on exactly where you want because it will stick hard immediately. I cut the excess off with the scissors and boom, was done in maybe 8min or less. I used a Ryobi heat gun after it was stuck on just to get the adhesive a little more stuck on. So far it’s been a few days and it’s been through a rain and a car wash. It’s stuck on perfectly, and looks fantastic. This is a must buy.

It has been 2 weeks since I installed the lip and can say it does the job. Remember to always clean with isopropyl alcohol before applying. I noticed the adhesive on the ends wasn't really holding so I ended up adding heavy duty 3m double sided tape which helped fastened the ends. The adhesive in the middle holds up very well. I have taken it to one car wash 1 week after letting the adhesive settle in and the lip still holds.

I love the idea of this simple add-on to give my car a more aggressive look on the front but this stuff sucks. I have a 2012 Focus Titanium and on each side of the front bumper on the bottom are two plastic trim pieces. I cleaned those with isopropyl alcohol to (hopefully) make sure it was clean. The driver side went on fine. Moved to the middle of the front bumper (painted) and finally worked my way around to the passenger side. By the time I was done, the driver side was already peeling off. Thinking I may not have cleaned it good enough, I used a Mr. Clean sponge (original) and WAY more alcohol and cleaned the plastic pieces very thoroughly. Or at least I thought. I also replaced the cheap tape with 3M trim tape. It stayed on a little better but I still struggled with getting it to adhere. The painted section was very sticking very well but the plastic pieces made using this stuff worthless. The outside temperature was also 90 degrees so there should have been no need to heat the tape. The other day I bumped a curb with it and it started peeling the drivers side off. Today, I noticed the passenger side was peeling off. I ended up yanking this crap off my car. And it's too bad because I really like how it looked on the car.

the lip looks amazing on my car, I have it installed on my K5 and it bends and adapts to the curbs of the car as advertised the only thing is that the adhesive included does not stick well, after 2 minutes it falls off. I tried using adhesion promoters and an additional 3m tape and it still went out . I have it installed using body screws and it holds tight and no longer has any issues with it, it allows you to use the shiny product without fading and or staining and it makes the car look lower while protecting my bumper.

Been through two front lips and was tired of wasting money. Figured I would try this and I actually love it. I rub it every time I come into my driveway no matter if I come in at an extreme angle. The best part is you wipe up the dirt from dragging it on the concrete and it’s still in perfect condition. Can’t go wrong with this product. Just make sure you cut slits on the extreme corners on your car if you have them like I did. Clean the area really good use a blow dryer to heat up the 3m tape and it sticks extremely well. Take your time and you will have perfect results. Watch the YouTube videos on how to install it.

As this product looked promising I was sadly disappointed from the adhesive section on a 1/4 of the strip did not stick at all. I touched the adhesive with my finger and in that section which what towards the end of my install and had me sticking power at all. My bumper was prepped a day before install and left parked in the garage. Pay a little more money for a bolt on.

I installed my first EZ lip pro on a colder day and did not take very well. I contacted customer care and they gave me some tips and tricks to make it adhere to the bumper better and even sent me a replacement at no charge! Make sure you heat up your bumper and the adhesive, or wait for a warmer day before installing.

Went on alright, looked good, actually really disappointed with the amount of money you spend on it and once the corners start peeling, there's no fixing it. Should have a peice that wraps around the wheel well to make the corners stay especially if you live in the midwest with all different weather. Extremely sad and disappointed.

Simplemente perfecto. Pega muy bien la cinta pero yo puse unos tornillos ya que sin el ya me pegaba en el garaje la defensa y por asegurar.... pero buena calidad y rapido de instalar. El precio un poco caro pero habia probado los baratos y nada que ver con este

Ottimo lip adesivo... L ho installato sulla mia mx5 Buona la marca... Buoni i materiali di ottima fatturazione ma soprattutto molto valido ed eficace il biadesivo presente nel lip per l installazione... Tempi di consegna perfetti come da aspettativa...

Me gusto que venga listo con cinta 3M para instalarse pero qun asi no hay que confiarse y mejor poner al menos 3 pijas para que no caiga a mitad de camino

Super bonne adhérence rajout de quelque rivet attention à bien positionner dès les débuts

Didn’t stick on too well. Had to super glue the thing on. It looks nice tho