Yamaha OEM , 704-82570-13-00-2

Q: Is this an exact replacement for a 2005 yamaha t50 tlrd?

Hi There, First, I assume your ignition switch is on a dashboard?? And your 50hp is not a tiller steered system?? This switch you are looking at is a "704" model - goes across a ton of marine / engine applications (Yamaha). 1. If the face plate is the same on your boat it is likely the one, (ignition key on top / Emerg. kill switch on bottom..) 2. pull off the access panel or look to where you can see the wiring under the dash (from the back of the switch..) 3. if it is a 704, you will see a large round harness (8 pins / female side) that hangs down and that snaps together with the male wiring plug that feeds to the boats electrical system 4. If it is a 704, you will also see 4 individual wires (GREEN , BLACK , RED , YELLOW) they plug into the color coded / corresponding wires that go to the boat as well. Very straight forward. * both of the items noted in points 3 and 4 are in the photos on the Amazon add. You can see what I am talking about.. Lastly, the cheaper non-Yamaha / Aftermarket / $50-60 version 704's have many reviews that note the plate is tad larger than the original Yamaha OEM switch. You may/will have to drill additional holes to mount it to the dash, I note this in my review. I spent and extra 100.00 for the OEM switch and for that reason - extra holes issue. Make sure to disconnect you main battery before unplugging and plugging the new switch -- reconnect the battery once you are done. Hope this helps..

Q: Will this work for a 2020 200hp yamaha v4 four stroke?

Hi Nicole .. I have a 2008, 250 V6 4 stroke and this was compatible with that engine.. Here is the advice i gave to another inquiry .. hope this helps.. First, I assume your ignition switch is on a dashboard?? This a "704" model ignition - goes across a ton of marine / engine applications (Yamaha). 1. If the face plate is the same on your boat it is likely the one, (ignition key on top / Emerg. kill switch on bottom..) 2. pull off the access panel or look to where you can see the wiring under the dash (from the back of the switch..) 3. if it is a 704, you will see a large round harness (8 pins / female side) that hangs down and that snaps together with the male wiring plug that feeds to the boats electrical system 4. If it is a 704, you will also see 4 individual wires (GREEN , BLACK , RED , YELLOW) they plug into the color coded / corresponding wires that go to the boat as well. Very straight forward. * both of the items noted in points 3 and 4 are in the photos on the Amazon add. You can see what I am talking about.. Lastly, the cheaper non-Yamaha / Aftermarket / $50-60 version 704's have many reviews that note the plate is tad larger than the original Yamaha OEM switch. You may/will have to drill additional holes to mount it to the dash, I note this in my review. I spent and extra 100.00 for the OEM switch and for that reason - extra holes issue. Make sure to disconnect you main battery before unplugging and plugging the new switch -- reconnect the battery once you are done. Hope this helps.. see less

产品编号: 73818311

安全交易

细节

Operation Mode
manual
Contact Type
Normally Open
Connector Type
2 Pin Screw
Brand
Yamaha Motor
Terminal
Screw
Item dimensions L x W x H
9 x 7 x 9

经常一起购买

描述

规格

Operation Mode	manual
Contact Type	Normally Open
Connector Type	2 Pin Screw Terminal
Brand	Yamaha Motor
Terminal	Screw
Item dimensions L x W x H	9 x 7 x 9 inches
Actuator Type	Mechanical
Contact Material	Copper
International Protection Rating	IP00
Number of Positions	8
Specification Met	Oem
Controller Type	Home Automation Controller
Control Method	Remote
Connectivity Protocol	X-10
Color	Black
Wattage	3E+3
Unit Count	1.0 Count
Number of Items	1
Manufacturer	Yamaha Motor
Item Weight	0.01 ounces
Product Dimensions	9 x 7 x 9 inches
Item model number	7048257013
Is Discontinued By Manufacturer	No
Manufacturer Part Number	704-82570-01-00
Voltage	12 Volts