ipolex SFP+ to RJ45 10Gb Module, Support 1G/2.5G/5G/10GBase-T RJ45 SFP+ Module, Compatible for Cisco SFP-10G-T, Ubiquiti UACC-CM-RJ45-MG, Mikrotik, Netgear, TP-Link, D-Link and More, up to 30 Meters

Using with a Ubiquiti Dream Machine Pro SE. configured port 10 for LAN instead of WAN. Came up with a EEPROM Error at first but it went away after 24 hours. Currently sitting at temperature of 67c. Connected at 10Gbps over existing CAT6, cable is about 80’ long maybe a lil shorter.

Using two of these on a Cisco 3650-48FQM running IOS XE 16.12.14 with no issues. The opposite ends connect to a Synology DS1825+ 2.5Gbps Ethernet ports.

Works great, doesn't appear to get as hot as some of the its competitors. Gives me a stable 5GBit/sec connection (max speed that my PC supports), which is great since while many of the other brands will do 2.5 or 10Gbit, not all support 5Gbit. Works great in combination with the Ugreen 2.5Gbit/10Gbit SPF+ switch (Amazon ASIN B0DY1R3S7N) didn't need to do any confiiguration, just plug it in and go.

First the specifics: I have this transceiver in the WAN port of my UDM PRO (set to Auto Negotiate) and connected to a 2.5Gb modem. The UDM side is seeing this as a 10Gb connection and the transceiver is correctly transforming the connection to 2.5Gb for the modem. Qualities: As with most if not all SFP+ to RJ45 transceivers, this unit gets hot. More importantly, it comes with a 3 year warranty which shows the manufacturer's trust in the product. Another important consideration is power draw as there is a wide disparity between brands. ipolex seems to be in the middle here although I didn't test this for myself. Experience: I can see from a speed test that I am getting nearly the entire 1.2Gb bandwidth promised by my ISP. Due to my configuration, I did not test at faster speeds. I got a little over a year with no problems and then started to have daily connectivity issues. After a few months of that, the transceiver died. It was difficult to figure out how to get warranty service since the manufacturer, like most, requires that I go through the retailer (Amazon) and Amazon doesn't make it easy to find the link. However, once I got to the correct screen and was now dealing directly with ipolex, the process went quickly and they replaced the faulty transceiver. Start to finish, I had the replacement in my hands in 4 days. Quality: One failure is not an indication of quality as I have had failures with every brand. I use that much equipment. Best I can say here is, let's see how long the replacement lasts.

This SFP+ module works exactly as advertized. My particular application is interfacing a 2.5gb ethernet machine to a 10gb ethernet switch. It does get significantly hotter that optical sfp+ modules even at idle, but a quiet 80mm fan blowing across the face of the switch appears to keep temps in control.

This unit is Compatible with Synology. Make sure the 10GB SFP+ Card is an intel board, not a CICSO. this transceiver works great

So I was skeptical about these as there was conflicting things saying that these only work with certain router manufacturers. Well I have used it on atleast 5 different router manufacturers and it worked great. They work with netgear and tp link just to name a couple of the bigger known manufacturers. Installation is simple and takes just a minute or two. Just make sure you have the module seated correctly in your device and it will just work as intended.

I purchased this item to use in my UniFi Dream Machine Pro. I inserted the ipoplex SFP+ into the WAN SFP+ slot in the UniFi Dream Machine Pro. The white link light illuminated and the UDM Pro allowed all my devices to connect to the internet. Everything seemed to work until I performed several speed test using different speed test sites. My Verizon Fios 1Gbps connection performed well when downloading but the upload speeds averaged between 5-10Mbps. I tried to manually set the speed on the SFP+ port to 1Gbps but that didn’t resolve the issue. I shutdown then turned on the UDM pro while the SFP+ was still connected but that didn’t resolve the poor upload speeds. I changed the WAN SFP+ port to autonegotiation then I shutdown the UDM Pro, turned on the UDM Pro, conducted speed test and the upload speeds were still averaging 5-12Mbps. I switched back to the 1Gbps WAN port, conducted speed test and my upload speeds were excellent (900Mbps - 922Mbps). I decided to purchase a SFP+ from Ubiquiti to see if the upload speeds on SFP+ WAN port on the UDM Pro will perform as expected. I initiated the return process for the Ipoplex but for now I’ll hold onto the Ipoplex in case the actual issue is the SFP+ WAN port on the UDM Pro. I’ll try the Ubiquiti SFP+ when it arrives. If the upload speed doesn’t improve I’ll know something is wrong with the SFP+ WAN port and not the Ipoplex or Ubiquiti SFP+ transceivers. Until then I have to give this product 1 star but I may have to upgrade it if the SFP+ WAN port is the culprit. The Ubiquiti SFP+ arrived and its working well. My FiOS 1Gb ISP connection download and upload speeds are as expected. Average download speed is 850Mbps and average upload speed is 900Mbps. The Ipoplex SFP+ have been returned. I will only use Ubiquiti SFP+ in my UDM Pro and US-16-XG.

Me sirvieron e hicieron ahorrrar mucho

Plugged it in to switch, and it just worked.

As described

Work with CRS305-1G-4S+IN

Supports 5g e on my unifi xg16. Very pleased - paired with a Qnap usb 3 5gbe adaptor.