PC CASE ATX Gaming PC Cases ，Mid-Tower USB 3.0 with Double Tempered Glass Full View Computer Cases Black (Fans are not Included) (H6)

Es un excelente case muy amplio me llego sin problemas y puse hacer una buena gestión de cablesExcelente 10/10, lo único malo es que los fans viene pre-instalado alrevez, aparte de que no son de una excelente calidad pero me siento muy satisfecho. Saludos desde Rep.Dom

Case works great, saw some reviews having issues with the fans but I changed them all out anyways. One issue i encountered is fitting my 360mm AIO inside, it would barely fit on the top, no way it would fit on the side. Not sure if this is on NZXT making their kraken elite v2 a bit larger, or if it’s on the case for being a bit smaller than advertised… eventually it got squeezed in with a little bit of bending but we still got the side panel on. Just beware if you’re planning on getting a 360, 240mm would fit but obviously look much smaller unless you added another fan. Has a decent amount of space for cables, although by the end of the build things were pretty tightly packed. Nice open slot for the PSU. Got the job done so no serious complaints

Pros:Looks very nice.Comes with 9 fans.Fits ATX motherboards (barely)Airflow is good (if you switch all fans around)Cons:Cheap RGB fans.Cable management is a nightmare because of the limited space on the second chamber.All fans installed backwards.A bit bigger than the original design brand. Not a big issue but think you will need a bit of extra space on your table.No dust filter on the side (where the fans sit).Glass is a fingerprint magnet.Other thoughts:It is obviously a close design to a more expensive case, but overall, the look is great. The first thing that you will see is that all fans were installed backwards. So, I adjusted that quickly. Then my motherboard does fit, but the connectors at the bottom were very tight. I would recommend that loosen up the fans at the bottom first, then put all connectors, and then remount the fans. Tested IO at the front and it worked well.RGB fans are terrible. The do work, but you can tell that the brightness, led distance and light diffusion are not that good. In my case, my motherboard did not come with the 3-pin connector, so I had to use a controller. My air intakes are at the bottom and the side, and my exhausts are on top and back. Since I am using an AIO with 2 fans, I changed the 2 fans with the top 2 fans and moved the 3rd fan from the top to the back. So, airflow is good on the case. I wish it also had a dust filter on the side.So, overall, it is a nice case. Just be aware that you may have some extra work to address some of the issues. In my case, I was able to get everything working, and for less money than if i would have gotten the known brand case.

Moved my old pc parts into this car and water cooled it for my son. Came out way better than I expected

Metal is a little thin but not in an awful way. Matte finish scuffs easily but paint seems durable. Mine came with broken front glass and amazon got me a replacement case shipped out immediately. I built in the original and swapped out the front glass. The fans are quiet, nice and bright and move decent amount of air but all fans moving air out of the case was a problem. I turned the top fans over to create some type of intake. I did the top fans for aesthetic reasons. To keep the easily seen fan faces showing. Not the best setup for thermals, flipping bottom fans would have been better but would have looked worse. It works well and looks amazing. Gets a lot of attention.

I absolutely do not recommend this case. This is one of the poorest and misleading cases I've ever built in. First off, an ATX board just barely fits in it. I had to take the board out, do all of my cable runs, and then install the board; even then, I had to get creative with some of the cable runs to make them fit. I also had to spend 20 minutes filing down razor-sharp edges and corners after slicing my finger wide open. The case is very flimsy as well. The fans are all set to exhaust, and I'm assuming they did this to make it look like you're getting reverse-blade ARGB fans. So you have to remove them all and reinstall them, but the cables barely fit once they are turned the correct way. Two of the fans had bad lighting, but it wasn't a big deal due to the fact I had to remove the lower fans because any GPU larger than a 3-slot card will lay on the fans. For an extra 10-20 dollars, you can get a much better case that won't twist and bend, cut you, and fit you're motherboard. We were excited to build in this, and that excitement was quickly filled with frustration.

Pc case came very well cable management was very good easy case to build in would recommend