TOOLIOM 50A Non High Frequency Plasma Cutter Non-Touch Pilot ARC 110/220V Dual Voltage Cutting Machine 1/2" Clean Cut

I have had this Plasma Cutter for almost a year now and have been really happy with it. I purchased it for a cnc cutting table as my old one was hf so would mess up the electronics. I have to say this little machine preforms better that my 1500.00 Miller and for the price you can't go wrong. The only problem I have had with it is recently the torch head stopped working and no matter how much I cleaned it could not get it to start working again. Bet the again I have cut a hell of a lot of metal with it.

first off wow! one of the best customer service i have ever had! second this machine is great! I am cutting up a old shipping frame to get project metal out, it is cutting like butter! it is super easy to set up right out of the box. depending on the air hose they send just use a heat gun on low and wala it will flex right into place and not leak. DO use tape on the threads on the reg, I put one of my qd on it and no issue, no leaks. I have run this on 220 and 110. works fine on either, BUT, HUGE warning and must do, if you change from 110 to 220 or other way around, you must!!!!!! wait and let the machine sit un plugged, it says 2 min, give it 5 min to be on the safe side. it senses the line voltage and the caps must be disscharges and then plug in with machine off!!! then turn it on and it take about 15 sec it will wake up, it senses the voltage then comes on. the fan is a high volume and quiet. the machine has not ever shut off on me while cutting thus C chanel apart. I have had many brands and kinds of cutters, welders etc, this is so far amazing! light and just flat out works, I use a wire brush to clean the tip now and then, and it is lasting a decent time so far, I marked the front gauge for the lower and upper air psi so its easy to see and make sure is right. i set it just above the .3 and it is ideal and running this on 35 on the read out, supposed to be 35A but it is working better then oxy asetaline! I don tneed to use the rest it comes with but I can see it being handy for some work. DO NOT just drop or throw down the torch as it has a ceramic cover, it will break, and I really like it better then some of the others with a black bakalite cover, they burn up any way then the brass end is open and it will stick to the work , haha, not fun. but this one is great. I LIKE IT!!! over all this gets A plus, and the seller also gets A ++ . I want to also add, I am using a small 150 PSI HF compressor I think it is 2.8 cfm but it keeps up just fine and will cycle and not just keep running so it is not over using the air supply! thi makes it very portable, also on the 120v plug i ran it on the 3500W inverter genny! it didnt grunt at all! ran it just fine. set at 20A and was cutting 1/8 angle , very pleased with this indeed!

worked for a second, then died, it was a lemon for sure, air issues, I've had one other unit that hasn't done this, so idk if its worth that hassle for you. Great option for the price if it works good. needs a huge breaker even on 110, normal wall socket wont cut anything. that's not made super clear.

I have orderd this and spend money on various consumables. Ive tried this on rusty and perfectly clean and new metal. The welder turns on, the welding capabilities of this welder are very poor. With both tig and stick. The plasma cutting works decently but still not the best. I would very much appreciate a refund without return for wasting my time. For someone looking for a reliable welder look for an onbrand or even a good used one. These welders are from companies like alibaba or temu bought for pennies on the dollar and sold to us for atleast twice as much. If i had known this i would have gotten a better one. I have no way of returning this and now im stuck with a welder that does not work. I was not even offered a replacement. The accuracy of this product is questionable. Ease of use is questionable. Appearance is nice but more than half is plastic/rubber. Value for money is not worth while. Stickiness is accurate since it welds your cunsumables and makes them get stuck onto your material. Heat retention is not something i think matters regarding this item but i will out that word in this to make sure it hits the too reviews.

I just took mine out of the box. Here are my thoughts: I read reviews that talked about air leaking. While the air hose provided is flimsy and does not seem like it will hold very long, mine worked out of the box. I made sure the clamps were good and tight and used plenty of teflon tape on the threads for the regulator. I'm sure I'll replace the hose soon. I do agree that the regulator is not the best. I will likely replace it. But mine has not leaked and seems to be accurate. It rates in MPa, not psi, which is not very helpful. I'm sure my first purchase will be a new gauge. With my machine, I bought a set of extra consumables (although a few come with the machine). In that separate purchase, a few small snap-on guides were included. Not the best, but better than freehand, which is what you'd need without a separate purchase. I cut through an 18ga piece of steel. It ran a clean cut in about three seconds right next to a cut of the same size that took me a few minutes with a grinder. I cut a piece of 3/8" steel and it went straight through when I was at the top 50 amp setting. Quite a bit of slag, but nothing I was worried about. I had been wanting a plasma cutter for a while, but didn't want to spend $1,000 for the one I had been eyeing. I finally pulled the trigger a couple of days ago when I was grinding a locked down piece of 18ga steel. The wheel of my grinder got caught up. The grinder flipped out of my hands and landed on my leg. Cut through thick canvas pants and into my thigh. No stitches, but I'll have a scar there forever. Bottom line, well worth the money and if you haven't used one of these before, you'll love it.

Enough power to cut 1/4 in steel plate without any problen, consumable are cheap to buy 👍 i torture the plasma cutter more than 1.5 h and cutting corroded bolts, cutting in rust, cutting in recess place... work perfectly

Mala calidad falló con muy pocas horas de trabajo

La manguera qué trae el paquete no es muy resistente. Tuve que ponerle manguera nueva(negra para alta presión). Pero si le recomiendo esta maquina. Corta muy bien. 👍🏽👍🏽👍🏽

These units are good. But cheaper for a reason. First the Regulator is pure trash. I just can't stop it from leaking air, I'm pretty sure it has a crack that my old eyes can see. Really should be used as a 220v and it will cut anything. You need clean dry air, very important and only 60-65 psi. I did have to re-tighten all exterior nuts & bolts. QC isn't the best. that should never happen. But I saved money :) Thinking of Tig next.

I finally tried the cutter, it will take trial and error in the setting of the air an voltage for satisfactory cutting. Lighter metal cut fine for me also I now have a method to cut stainless steel and aluminum . This appears to be a satisfactory machine for home use. I’m used to an industrial cutter but I feel this will serve me well for home and hobby. Have fun hobbyists with this.