Will these https://www.amazon.com/dp/b07szmk7cs?ref=myi_title_dp work with this set? so if i buy both they will fit together?

Hello. Thanks for asking. So it's from one set. https://www.amazon.com/dp/b07szmk7cs?ref=myi_title_dp This set consists of the 4 largest molds of the set https://www.amazon.com/dp/B071FT57FF?ref=myi_title_dp Usually this set is bought as an adjunct for faster stone production. If you have any questions, please contact us - we will help Have a nice day. Sincerely, Alexander.

Why don’t you include complete directions with your product?

Step 1 Prepare Mold - Before mixing the concrete, make sure the mold is clean and clear of dirt; - If it has been used before, clean it up with soapy water or a solution of citric acid; - Simply brush a little bit of light vegetable oil or mold release in the form. Using mold release is recommended but not necessary - Not using mold release can make the stones more difficult to demould, and you’ll need to be more careful about damaging the mold. But too much mold release will make air bubbles in the surface. Step 2 Mix Concrete - When mixing concrete, always wear proper safety equipment (rubber gloves and a particle mask); - Mixing can be done with a proper concrete mixer, in a wheel barrow with a concrete hoe. or by hand with a trowel in a bucket; - If you re mixing by hand, it’s really important to take your time and get everything completely mixed Tip; - For preparation of concrete using high-grade cement, slag-free. Sand should not contain impurities clay. To reduce the amount of water in the solution, be sure to add the plasticizer concrete on the maximum recommended by the manufacturer. Number of plasticizer is calculated with respect to the cement. When mixing concrete, use 1 part cement, two parts sand. The solution should not be highly liquid. To check him take in his hand, he must not flow through parted fingers. - You can watch videos in YouTube https://www.youtube.com/watch?v=9SC_HmvAezk Step 3 Fill Mold - Fill bottom surface of mold with 1/2" of concrete and pat it down vigorously to drive out air bubbles; - Then fill the mold completely to the top and smooth the top surface with your hands so the concrete is flat and level; - Finish by tapping and shaking the mold, driving out as many air bubbles as possible. Step 4 Cure and Demould - After the mold is full, place the mold on a level tabletop; - Cover with plastic film and wait less than 24 hours to cure; - The plastic film covering the concrete will help keep the humidity inside, like a greenhouse, and this will minimize surface cracking; - After the stone has cured then carefully pulling up gradually on all sides until it pops off. And it's All. Your stones are ready to use !!!

What kind of color do you need to use to color the concrete ?

Hello. For painting finished products, I use technology ACID STAIN More information on this technology can be found on the Internet. Also, I recommend using different tones. This will give the finished product a more natural look. You can also cover a finished product in several layers that will give a more intense color. If you have any questions, please contact us - we will help Sincerely, Alexander

How did the other users "cut" the stones, like I see in one of the pictures? Were they cut with a masonry saw, or were they molded that way?

Put a piece of plastic wrapped board or something similar in the frame where you want the "cut" prior to dumping in the concrete - no cutting needed.

Desertcart Logo

交付 Malaysia

获得最佳体验获取应用程序

下载应用程序

我们从

阿联酋
英国
印度
美国
日本
KOREA

客户服务

关于我们

客户支持

描述

🛠️ Mold your dream garden path—because your outdoor space deserves a glow-up!

ROBUST REUSABLE - Made from sturdy ABS plastic (1.9-2 mm thick), these molds withstand repeated use without losing shape.
CUSTOMIZABLE AESTHETIC - Paint your concrete stones any color to match your style and elevate your yard’s vibe.
EFFORTLESS DIY UPGRADE - Lightweight and easy to handle, these molds empower you to create professional-looking patios without hiring out.
GENEROUS CASTING SURFACE - Cover up to 0.37 square meters per set, perfect for transforming your outdoor space efficiently.
CRAFT YOUR SIGNATURE PATHWAY - Six distinct textured molds let you design personalized garden paths that stand out.

This set of 6 ABS plastic flagstone molds offers a 0.37 m² casting area with varied textures and 38 mm thickness, enabling durable, customizable concrete paving stones for garden paths and patios. Lightweight and reusable, they provide a cost-effective DIY solution to elevate your outdoor living space.