Broan-NuTone SP2404 Backsplash Range Hood Wall Shield for Kitchen, Stainless Steel, 24" x 24"

It arrived in perfect condition. Easy to install. Easy to clean. I got it in stainless steel so it's not reversible. It matches appliances perfectly.

Just purchased a stove that doesn’t have the part in the back that is above the burners. My current tile backsplash showed so I needed something to cover the gap. I didn’t even know these existed until now. WOW! This is perfect since it’s designed for behind a stove. Very sturdy and installed in a minute. I bought stainless steel screws for installation. Looks fantastic with my stainless steel stove. Matches beautifully and clean up is a breeze! Highly recommend this item.

After getting new appliances, the oven we chose didn’t have any kind of backsplash. Since we’ll eventually put in tile, we decided on this for an oven backsplash. It was actually thicker than I thought it would be after reading some reviews. I’d have to agree with other reviewers that screws should have been provided. I didn’t have any issues wit bent corners or scratches. It came packaged like a painting. I did go out and buy some drywall anchors and screws (#10 or 3/16”). After peeling only the corners of the protective film, I put it where I wanted and with the help of another person, marked the screw holes. I will have to say that doing this BEFORE the installation of the stove would have made this a whole lot easier. As it was I had to pull the oven out because the backsplash extended below the back of the oven. I did run into the issue of putting it as high as I could that made drilling and then screwing in the screws a little difficult (drill clearance). Initially I left the screws a little loose so I could have a little maneuvering room while installing the screws (a two person job, unless you’re putting on some kind of adhesive). Unless you are below eye level of the microwave you don’t even see the screws. After I tightened all the screws I removed the protective film. If you’re using only adhesive, I’d make sure you’re hold it as pulling off the film made the backsplash bow. If I didn’t use wall anchors I can see it pulling out of the wall. Overall it didn’t take that long to install. I like the finished look as it matches the other appliances.

Product arrived quickly but was slightly damaged in the bottom left corner during shipping. I was able to use a rubber mallet and piece of wood to smooth out the dent and crease. Not a huge issue to me as that portion is located out of sight behind my oven. Otherwise, the installation was very simple using 4 screws and plastic anchors (not included) plus some construction adhesive on the backside. It looks great and matches my existing stainless fixtures (oven vent hood, oven, fridge, etc.) perfectly. It does show fingerprints, but wipes off and cleans up very easily.

I must say that this product is excellet. Why? It was sent in a box that is strong and dent-proof. The measurements are precise. Predrilled 4 holes so it was ready for installation. I must also thank to delivery, on time and with care (this time Amazon delivery was made by our local Usps).Yes, it is stainless steel and can hold magnets. Just what i was looking for. A little bit pricey though…

nice worth the price

I feel like this could have been cheaper. It's just a thin sheet of metal you apply to the back oven wall. It's easy to clean and looks industrial. Installation was super simple and it paired well with my Cosmo range hood. It arrived without damage and sits flat against the wall.

This review is for the Broan-NuTone SP3604 Backsplash Range Hood Wall Shield for Kitchen, Stainless Steel, 24" x 36":After getting a new range, I needed a new back splash. WALA! Found this one! It perfectly matches the range hood I got (at the local home-improvement store). The 36" x 24" worked out well. We installed the back splash first and didn't use the top mounting screws (sold separately), since a range hood covered it.To answer some frequent inquiries I've seen: Yes, it can be drilled through -- we drilled pilot holes, then used self-drilling screws (bottom only). No, the double-sided tape won't hold it up long term, but held long enough to keep it place while we finished the mounting process. And yes, it can be cut -- lay flat on plywood, use a dremel tool with a saw blade for metal (okay, stock up -- we used more than one!), and take your time; results are worth it! And finally, yes, it IS magnetic. (Pic included -- notice the light switch notch we had to cut, and the hanging kitchen utensils!)Would buy again; hope I don't have to! :)