Instant Ocean HoldFast Epoxy Stick, Fish Safe 4 oz

Bought two of these little tubes to "cement" my rockwork together in my saltwater tank and used about a tube an a half. I had about 120 pounds of rock that I wanted to form into a few structures in my 75 gallon tank and this stuff worked beautifully! I had been letting my rock cure in large tubs with a circulation pump for a few weeks, so they were still very wet when I used this epoxy to hold them together and it still became rock hard and my structure is SO sturdy. I created a large archway and a complete hollow circle through the rocks. Neither of these are very sturdy structure alone, but with the epoxy I could grab the center of the archway and pick it up with no breaking and no worries. I would absolutely use this product again if I ever need to do another aquascape. It dries stark white, but will soon enough be covered by beautiful coralline algae, so no worries. A few notes: -This is NOT glue. It is NOT sticky. It will NOT "hold" two pieces of rock together. You cannot simply plop a piece of this epoxy on the bottom rock and shove your other rock on top and expect it to hold. It will NOT hold. I found the best way to ensure a sound structure was to position the two pieces of rock exactly how I wanted them and then completely encircle the seam of the two pieces with this epoxy being sure to shove as much as possible into nooks and crannies on each piece of rock as I went around and then smoothing the epoxy a bit up the side of each piece of rock. It works the best if the two pieces of rock can already stay balanced on top of each other without moving without the epoxy. Otherwise you'll just have to hold them until the epoxy begins to harden. -Keep a cup of water close by while you work. As you are mixing the epoxy, dip a finger or two in the water and continue working it. The little bit of water helps it mix much easier and faster and allows it to soften up just a bit so you can get more into the nooks and crannies of each rock. When you get the epoxy mixed and are ready to place it around your rock, dip a finger or two back in the water. Use these fingers to work with the epoxy on the rock. This helps the epoxy stick to the rock and not your fingers and allows you to smooth it out around the rock pieces and into the nooks and crannies. -Let the epoxy harden a couple of days before moving the rock or submerging it in water. I let mine cure about 35ish hours before doing anything with it. I did want my rocks to stay moist, so I poured a bit of saltwater over them periodically and this did not seem to mess up the epoxy at all, but I would be cautious about completely submerging it too soon. I know this was long, but I wanted yall to have an honest review and a few helpful tips! I hope it helped yall out!

I use this to secure my dry rock together when creating a reef aquascape and also for attaching frags. When attaching frags to live rock, you must add superglue gel to both the epoxy side and the live rock side of the epoxy. You basically sandwich the epoxy between superglue gel or it's not going to adhere correctly. It's aggravating at first but if you continue to attach your frags this way you will get better at it. I find when the epoxy is used in water never gets totally hard but stays somewhat gummy. However when used on dry rock and allowed to cure for 24 hours it becomes rock hard. I had to remove a rock from another after 24 hours and it took me beating the rock with a hammer to get the cured epoxy to break. I've also let balls of just epoxy dry accidentally and they next days they are basically rocks themselves. Tips for aquascaping with dry rock: use the little broken pieces from the rock to stick into the epoxy joints you make to help hide the epoxy. Do this under 10 min or so or it will be too hard by then. On rocks that just aren't stable enough and want to roll, you can add little "feet" that stabilize the rock, to keep the "feet" from sticking to the surface they are sitting on, just apply some of the rock dust particles that fall off the dry rock. I've never tried one of the other brands of reef epoxy as this one is cheap ( on Amazon anyway never in any of my local stores) and I've had good luck with it. The only negative is the color, it dries totally white. Which is fine if you are aquascaping with white dry rock but it does show badly on live rock under frags. In the attached pic, most all of the rock is epoxied together, some of these rocks weigh several pounds and didn't balance very well, where the where natural holes in the rock (back side) I did use some zip ties to also help stabilize the rock. Update 9/11/2018- Was almost out so I ordered more and it appeared I would be receiving the new coralline purple color, product came and it was the green dries to white version, so not really happy I wasn't sent the pictured product. Update 3/6/2019- Still using this product, I've used numerous tubes since beginning the hobby and will continue to do so, as this stuff holds up well and is inexpensive. Update 8/18/2020- I still use the same exact method of attaching frags and have not had any issues with my reef aquascape coming apart. If anything, I have difficulty getting frags off, if I decide to move something later.

I bought this epoxy to hold together rocks and driftwood for my aquarium. It wasn’t so great at that. While I was using it some got stuck on my long fingernail which happened to be cracked. It cured on my nail and now the crack is fixed. Won’t be using for my aquarium again but I will be using this to fix my long nails.

Excellent

Not easy to use

Buena resistencia y precio

Worked great for creating my rock scape! Super easy to use

Der erste Epoxy Unterwasserkleber mit dem ich wirklich zufrieden bin. Lässt sich super leicht verarbeiten, wird schnell fest, scheint keine Nebelschwaden ins Aquarium abzugeben beim anbringen unter Wasser. Habe bisher allerdings nur einen relativ kleinen Korallenableger damit befestigt, von daher kann ich noch nicht abschließend beurteilen, wie stabil er langzeit auch bei größeren Korallen ist. Werde das ggf. noch updaten. Bei anderen Herstellern (z.B. Aqua Medic) gab es entweder diese Eintrübungen im Wasser, was je nach Menge auch schädlich für die Fische sein kann (hat mir einmal 5 Fische gekostet, nie wieder!), oder aber der Kleber hat quasi überhaupt keine Haftkraft. Von daher (vorläufig) 5 Sterne!