HulkFit Multi-Function Power Cage Rack Crossfit Attachments, J-Hooks, Dip Bars, Weight Plate Holders, T-Bar Row Platform, Barbell Clamp Collars, Hangers and Others

This fits the HulkFit cage, however, it does not sit flat! After placing my bumper plate on, the plate slid off!! Very unsafe! I ordered 4 of these and all of them have a different fit. The worst one is pictured.

As others have mentioned, the weight racks do not align properly with the Hulkfit cage and causes plates to slide off. I am not sure if this is due to misaligned holes of the hulkfit cage, or poor welding of the weight racks or both. After 3 months of use, the racks seem to have declined even further. This is extremely dangerous if you have pets or children.

On my end, I have the FitnessReality 810XLT (or the Progear 1600) squat rack that utilizes 2" x 2" supports and MANY extra holes that fit an M10 sized bolt (the same bolts that come with these hangers). As shown in one of the pictures attached, the bolt holes did not fully align with the HulkFit hangers, though they both did fit a M10 sized bolt. In addition, the hanger was slightly wider than 2" in the inner part; as a result, there was a gap as well. To address the fit, I downsized the bolts to M8, and added metal washers in between until the fit was snug.Unfortunately, the hanger bends when holder bars GREATER than 45 lb. As shown, my 75 lb hex bar was slightly too heavy and bent my hanger, though the hanger's held up well over half a year since I installed this on my rack. Whether or not you have the appropriate HulkFit rack, this is also a great fit for squat racks with 2" x 2" supports. It greatly organized my home gym, as shown. I will always recommend these hangers to others for the price and great value of these.

Purchased 2 sets of the weight holders but all are being returned. Each of the pins were poorly aligned when they were welded and the angles of each bend were off. Could not even attach to rack and were therefore unusable.

This review is for the HulkFit weight holders. I’ve noticed amazon tends to group all HulkFit reviews into one mass reviews so hopefully this will clarify what I am reviewing.After singing praise for the HulkFit power rack I am sorely disappointed when it comes to the HulkFit weight holders. Like others have stated good weight holders will have a slight angle upward to ensure weights don’t slide off. However these weight holders are straight and flat no angle at all to them, I would be super leery putting these high up on my power rack as such I have them on the 2nd to lowest space near the bottom of the rack. Now I am not one to really care about looks, since the whole purpose of these are to hold heavy weights, but man the welds and QC on these weight holders are terrible. On the lip of one weight holder there is a bump of metal, doesn’t really prevent me from racking my weights but it sure is an eye sore. Also there are poor welds, scratches all up and down the weight holder peg itself just not fun to look at.Fundamentally though do these things do their job? Yes they hold the weights in place and for that I will give 3 stars. However having bought and used the Yes4All 2x3 weight holder, man the Yes4All is just heads and tails better than the HulkFit in terms of usage, aesthetic, etc. I’ve included photos of the HulkFit and Yes4All so you can see the differences between the 2. Yes4All weight pegs aim up and have a rubber ring to prevent plates from hitting flat against the rack but the pole/sizing is not perfect for the rack. HulkFit pegs are straight, aesthetically not appealing, but the sizing fits the rack perfectly and does the job.What I find helpful for the HulkFit weight holder is taking a piece of plastic and placing it under the weight pegs to give it a slight angle upward.Overall if you need weight pegs and want the right hole/sizing for your power rack get these but understand there’s a lot of flaws.Amazon messed up my photo upload for some reason so here's what they are:Photo 1 - Metal bump on the lip of the HulkFit weight holderPhoto 2 - HulkFit weight holder with a UHMW plastic underneath it giving it an upward anglePhoto 3 - Bad welds/scratches on the HulkFit weight holderPhoto 4 - HulkFit weight holder with a UHMW plastic underneath it giving it an upward angle with a Bumper Plate in itPhoto 5 - Yes4All 2x3 weight holder, you can see that the sizing is off since it doesn't go across the entire rack frame but the peg angles upwards and there's a black plastic ring protecting the rackPhoto 6 - UHMW plastic I placed underneath the HulkFit weight holderPhoto 7 - HulkFit weight holder and how straight/angled slightly down the weight holder is

I ordered the jhooks/weight holders/and dip barsThey all have some quality defects or some minor functionality issues. The biggest one is the weight holders they don't "incline" they should have a 3+ degree upward tilt ideally. I used a piece of wood to prop them up this is why folks are finding they can bend or at the least weights fall off. A minor incline would prevent most of this. The j-hooks aren't as deep as i'd like and generally expect, and the dip bars came with a slight bend in the 1-inch peg but they work. The metal in the part that goes around the rack had some cracks in the corners.The good. They are cheap, and I wanted to report fit powertec very closely. Powertec makes nice stuff but won't be buying powertec brand again because they use non standard tube dimensions and charge an insane amount of money for extra parts. I'd normally just stick iwth a 2x2 (Best) or even 3x3 tube for a more expensive squat rack so i can get parts. Generally, they are good enough. I can buy three of these jhooks for the cost of one powertec.

The weight holders are very solid product like something you would expect from Hulkfit, however one of the holders like other reviewers have said has a slight angle toward the ground instead of up which in theory could cause injury. It shouldn't be an issue for myself since I leave them at foot height anyway. It may be of concern if you have it up off the ground a 3 or 4 feet so just something to watch for.

False advertising.My rack is 2x2 and this was clearly made for 2.5x2.5 tubes.Because of the size discrepancy, when attached to my rack these holders were sloped about 15 degrees below 0.This is of course super dangerous for your children, your pets, and most importantly, your floor.Since I can't find reasonably priced 2x2 olympic weight plate attachments anywhere else, I settled for two pairs and bought adhesive foam to fill in the extra space between these holders and the rack tubes, helping them stay just over the 0 degree line.I use two pairs of these on the AmStaf TP006D Power/Squat Rack.It works, but it's a cheap makeshift solution. I will be keeping an eye out for alternatives.

This is a well made Add-on for a home Rack setup. The seller should add the measurements to this unit as it was buyer description that helped me figure out if it would work on my unit. I have a AmStaff Rack which has 2.5" Tubing verse 2" tubing on some. AmStaff / Hulkfit and a few other names are all made from the same companies and re-branded hence many items are interchangeable. I really like that these have padding on the inside so it does not scratch up your rack. For those of you wondering the length of the weight tube is just under 9"

Peak times at the gym barbell clamps, especially the quick release kind, are hard to find! Was wasting too much of my trainers' time just searching for a pair of these when setting ourselves up for my workout... only to discover that when we did succeed in finding a pair they'd get stolen by someone else (hoping we were done with them) if we happened to put them down for a moment to add some plates.Problem solved!Spotted these at $10 - at that price it's worth bringing my own to the gym! Purchased a Pink pair (turned out to be a very nice mauve/pink shade - not the bright pink shown here) due to the gym using only Black ones - Hoping the color would deter the big burly fellows from "borrowing" them. They are light & so easy to carry to & from the gym (worth it for the time it saves me hunting a pair down once I'm there.)They are a hit! My trainer loves them & other trainers have been eyeing them, many asking where to get a pair for themselves. With a few different bright colors available I'm still safe with my pink ones - and being able to spot them from a distance - No one will be walking away with my set!

These are made for 2.5"x2.5" racks... NOT 2"x2" racks. I am annoyed about the sizing issue, but the storage pins are solid otherwise.

Very well built. Strong steel and the swivel action up/down and side-to-side works perfectly. It is made to work with both 1"Standard size bars as well as 2" Olympic size bars, and has an easy turn knob to tighten against the bar you are using to prevent it from accidentally sliding out when in use. Would highly recommend them.

I am not sure i did not do it right or the product is not manufactured properly. the two big nob screw are two thick for the holes. they just go in a little bit and the can not go any deeper. Do i have to just twist it really hard so that it will eventually go in? i am worried i might damage the threads. might have to return it.

As other customers have said, the screws do not fit. It will probably cross thread and damage if you force it. Luckily I don't use the screw on the bar holder, so I just went to Home depot to buy a long bolt, washers, and a locking nut to attach to my rack. This costed about $3 but this was still the cheapest landmine I could find so it works for me.

This fits perfectly for my Powertec PowerRac! Cheapest option vs other brands. Fast shipping and I'll be buying another set at this price!Note - its 2.5" x 2.5" measurements. A lot of people complained because it didn't fit theirs. Make sure your cage has a 2.5" x 2.5" post with 1" holes.

High quality and great shipping. They are definitely built for 2” x 2” racks. Mine is slightly smaller but it still works. If you glue a small wedge of wood to the inside, it works great and holds the weights so they don’t slide off. Overall, great value

Bought a set last week and loved them so much I ordered as second so I could use on a second bar for super sets. They keep the weight in place and pop off easily. If you’re using spring collar clips then do yourself a favor and spend the money on these.

First item the bolts were incorrect size and the holes for them weren’t even threaded correctly 🤦‍♂️Second order/replacement had silver branding and seemed to be a nicer build but this time I got 2 different sized bolts one fit to attach to gym frame but the bolt for securing you bar was way off another failure. I returned one and kept the second and will head to the hardware store to complete the item

PROS:- Fits 2" Olympic Bars- Constructed of sturdy nylon resin with rubber slip pads- Affordable at $12- Secure grip (Tested with 245lbs of weight)- Several colours to choose from- 2 year warrantyCONS:- Lock release mechanism is nylon resin and MAY break easyOVERALL:For the price of $12 you can't go wrong, especially when backed by a 2 year warranty!

Works great and fits good. How long will it last time will tell. If this was metal I would have no doubt but this is plastic so who knows. For now I have been using it for couple weeks in the gym and all is well.

It's a little wobbly but so far it works great. If you wanted you could put an extra washer where the base attaches to the landmine to snug it up so it doesn't wiggle but I wish I didn't have to.Other than the wobble this feels sturdy and for the price it was a great deal!

Finally got around to using this yesterday. I bolted it to my deadlift platform and did some t bar rows with it working up to 8 plates. It held up to the weight and seems very sturdy. I couldn't find a cheaper comparable model anywhere on the internet. 5/5 stars for sure. Bang got your buck is unbeatable