MOOCY 8" Small Hard Case with Pluck Foam Insert, 8.6 x 4.9 x 1.9 Inch - Watertight Padded Plastic Box Protect Tools,and Glass Testing Equipment

Works great for what I wanted. Fits my clamp meter and modular test lead set. Feels sturdy and has a nice gasket.

I recently purchased a new IWATA Eclipse Takumi ECL350T airbrush here on Amazon and because this is a side fed airbrush that uses primarily attachable paint cups and side fed bottles unlike any other airbrush I currently own. I decided to purchase this case that I had been eyeing for some time but just couldn’t justify the purchase. Well I’m pleasantly surprised with this MOOCY protective case. It’s the perfect size to store an airbrush and its necessary accesories. The case comes with a customizable foam insert that breaks apart into squares which allows you to form fit your stored item within this case. The case is made of durable plastic with a hinged lid that will allow this case to open and close as often as needed without the lid eventually breaking away from the case. Two front panel clips lock firmly and securely in place. This case allows me to store this airbrush and its accessories in one place in one case. The case is water tight with a rubber seal installed to the cases lid trim. The customizing of the foam insert was far easier than I anticipated. The case has two places on it where if needed you can add an additional layer of proctection of your cases contents by using very small pad locks or zip ties in the provide molded holes on the case. I’m overly impressed, you get a well made protective, portable storage case for your money. RECOMMENDED!!!🏆

This happens to be a perfect case to store silver bars. PAMP 10oz bars stack 3 high and 3 wide, with the bottom and top padding on.There are 3 pads, top, bottom, and middle. The middle one I removed. It has squares so you could punch some out, and keep things very secured.Many reviews talked about waterproof, that isn't a priority for me but cool nonetheless.

Very nice and well built case. Unfortunately, right out of the box left lock fell off before even I opened the case. Small glue residual on the bottom of the clamp suggests that it was not glued properly. Otherwise pretty good quality, just need to apply some crazy glue to fix it.

Great little case that fits my GoPro 8 batteries perfectly. Foam is precut and there are plenty of spots to fill it out with batteries.Overall this looks and feels of good quality and I’m happy with it.

I am using this product for the Teenage Engineering K.O. II. It has been difficult for me to find a case for the KO II that I feel can adequately protect the device. Analog cases has preorders for a soft “hard shell” case for $46 but I wanted something available now. Enter the MOOCY 10" Small Hard Case with Foam Insert, 10.8 x 8.6 x 3.7 Inch - Watertight Padded Case. While it is a little bulky for such a slim unit, I think it scores points for the level of protection offered at a low pricepoint of around $30 all in via Amazon. All I needed to do was swap the included large form insert for something about 1cm thinner and it is good to go (I used the modified thick insert along with the provided thin insert for a fit that is just snug enough to keep the unit from moving in the case when it is closed but not too tight when closing the case). I also trimmed down the foam on top to avoid pressure on the knobs and faders as an extra safety precaution with “fadergate” being an issue for some and the fact that I have one of the units from the first shipment. Chocolate bar for scale. Hope this helps someone.

I am skeptical of "waterproof" claims. Other cases I've tried have claimed to be waterproof, but failed the submersion test. This Moocy case, however, PASSED. I filled a small plastic tub with water, put a paper towel inside the case, closed it, then submerged it for a few seconds. I then completely dried it off and opened it up. I was pleasantly surprised that the paper towel wasn't wet at all. So that part is good. It is waterproof. The seal doesn't feel snug like some cases, but I guess it's tight enough since it passed the test.The bad part about this case is that the foam padding doesn't come up enough from the bottom, or down enough from the top, so the foam doesn't touch. Meaning some small items may move around when the case is moved. This could be an easy fix from the manufacturer: just add a tiny bit more foam.I love that there are layers of foam. The top layer is 2 cubes high (cubes are combined).I would be returning the case had I been using this for professional grade equipment, but since it's for something inexpensive I'm probably going to keep it.

nice case similar to my pelican . has foam where pelican does not supply foam with their small cases any more. that's why I buy this case now .