BetterVent Indoor Dryer Vent by ADR Products | No Water - No Mess | Save Energy while Enhancing Indoor Air Quality | For Electric Dryers | Made in the USA

My husband installed ours this morning, and I am already impressed. When our house was built the dryer was vented up a tube in the wall and out a vent on the roof. My husband didn't like cleaning out the tube, so he vented the dryer out into the garage - but lint seemed to be getting everywhere with the lint catcher he was using. This looks like it will solve the problem, and the installation was really easy.UPDATEWe have been using this for a couple weeks now and are very happy with it. The only thing we thing the manufacturer should change is the changeable filter. We experimented with various filters and determined the following after installing the vent and weighting the change your filter door as per the instructions:(1) The changeable filters that comes with the vent are too lightweight and almost impossible to clean. The change your filter door popped up after only 3 loads - with little lint on the filter.(2) I then tried just the metal filter - which never popped up the change your filterdoor - but blew small particles of lint into the garage and all over the car. I had to use a Swiffer duster to clean up the mess.(2) I next tried a 3/4 inch thick washable filter cut from a a/c filter (about the same thickness as the filters that came with the vent) - and while it was easier to clean, the change your filter door popped up after 6 loads - with a moderate amount of lint in the filter.(3) I next tried a 1/4 inch thick washable a/c filter - which was the easiest to clean, and the change your filter door didn't pop up until 10 loads - or a week of laundry. I will be purchasing the 1/4 inch a/c filter and cutting multiple filters for the vent at quite a bit if savings over the filters that can be purchased from the manufacturer. They also work much better than the ones provided by the manufacturer.The pictures below are of the installation in the garage with the change your filter door popped up, and the metal filter and 1/4 inch a/c filter after 10 loads (1 week) of laundry. This appears to be the right combination for maximum efficiency and longest filter use between changes.Update 2 - 10/20/16I have added a picture of the filters I experimented with. The green and black ones on the top work best. The blue one (I tried 1/2 in. & 1/4 in. were as bad as the filter provided by the manufacturer. The denser the filter the less loads. The two less dense/light weight filters did as good as of a job at blocking the lint as the denser filters.Filters in picture:1) The green filter is from the cheapest whole house a/c filter my husband could find. It's about 1/8 inch thick. My husband had to remove it from the cardboard frame it came in. This worked as well as the black filter - about 10 loads. These are not washable at all - must be tosed after using.2) The black filter is a foam window unit a/c filter, about 1/8 inch thick - it was the cheapest and worked as well as the green filter - about 10 loads. This was the most washable - but since they are cheap - I have been throwing them away after one use.3) The blue filter is made out of dense fiberglass or natural hog hair (not sure which) - I tried 1/2 inch thick and 1/4 inch. The 1/2 inch thick one worked as poorly as the one provided by the manufacturer of the dryer vent. The 1/4 one worked slightly better. These are supposed to be washable - maybe with a power washer?4) The white/blue filter is the one provided by the manufacturer - I got the least amount of loads with it (it and the 1/2 inch blue filter) - and it really isn't very washable.Update 3 03/26/2017 - Magnet WeightsI have found that over time the glue on the magnet weights degrades and the magnets fall down into the vent. I would recommend putting the magnets on the top of the pop-up flap and not the underside. It's still a very good solution to my dryer venting needs - perhaps just needs a few design changes.Update 4 07/22/2017I've added more pictures of my filter solution. The cheap ($2.94 packet of 4 20x25x1 fiberglass air filters) Flanders Easy Flow green filters from Walmart are the best. (I couldn't find them on Amazon). Just pull off the cardboard and you can cut out 6 filters from one big filter. Use care as fiberglass can poke you - using gloves while doing the cutting can eliminate that problem.As I said in another update - double up the filters in the unit. I replace the one closest to the air flow once every week to week and a half. The other about once a month. In the pictures I've added you can see how well this traps the lint - keeping it from escaping into my garage.I still highly endorse the vent - just not their filters and magnet weights - but by trail and error found good solutions.

My dryer vent duct exists through the roof top, and when I noticed everything in my laundry room covered with a frank amount of dust after laundering some blankets, I figured the ducts needed cleaning. A few minutes into the procedure the service man informed me that the duct was never installed correctly, was not connected to the outside roof vent cap, and was in fact too short to couple with it. That meant then all that dryer lint and dust was simply blowing into the attic space. He told me he did not have enough ladder length to enable him to reach it, and suggested I call another service. After calling numerous companies that install dryer vent ducting, not one was interested in the job, and it was suggested I call a building contractor. I had a better idea.Following a quick search for options, I came across indoor vent systems, and ultimately decided on the BetterVent Indoor Dryer Vent system, also purchasing the flexible transition duct and an end cap for the installed wall duct. I chose it because it is not bulky, doesn't take up floor space or interfere with movement around the dryer, and its attractive. It was quick and super easy to install, and I did it myself. It really does the job too. No more dust everywhere, no more fear of lint fire hazard, and no more paying someone to clean the ducts. I can do it all and keep my money!Look at the photos. #1 – screen with filter after 10 dryer loads, #2– dirty screen before vacuuming, #3 – polyester filter before vacuuming, #4 polyester filter after vacuuming. #5 – installed systemThe filter vacuums very well and I expect will last a long time. I recommend this system 100% for ease of installation, effectiveness, ease of cleaning, and overall appearance.

First, make sure you install a few inches below any ceiling or shelf. I pur mine flush and had to reinstall. On top is the latch that let's you know when to clean the filter, by flipping up.Overall I am happy.Filter must be cleaned every 3-5 loads. But it is very simple. I remove mine. Use the dustbuster to vacuum it. Takes me 20 seconds. I did buy an extra 3 filters, so weeks I'm busy or lazy, I can just pop a new one in and put the other aside until I can clean it.The humidity. Ok. This thing is going to make whatever room it is venting into feel like weak sauna. At first I was like, yeah, this isn't going to work. But what I realized was, it isn't making any other room hot, and I don't hang in the laundry room. So I think it will work.That said, it is winter and heat and humidity is a hot commodity around here. I could be writing a different review come summer.The trap works as expected. The cleaning is easy. The 4 screw installation was easy. Overall, I would suggest this to anyone getting tired of cleaning out 30 foot of tube up in the crawl space like I had to do before this.

Awesome deal works great up to the moment it’s doing it’s job. I’m using it on a gas dryer machine that’s located in the laundry room outside my house.