XS SIGHTS Big Dot Shotgun Front Sights, Non-Tritium

Quality products

I recently purchased a Mossberg 590 FLEX Tactical 12 gauge shotgun that has a tiny little bead as the front sight. Since it was difficult to see that little bead I searched and found XS SIGHTS. There were several choices and I decided to get the Big Dot Yellow sight. What a difference!! It is really bright and very easy to see. Since XS SIGHTS is very popular I was able to find YouTube videos that showed how to install the front sight on my shotgun. It really is easy to install and the whole process was a breeze. This shotgun is going to be my home defense weapon and that Big Dot Yellow sight is very visible in the dark so I will have no issues with aiming at my target. I recommend XS SIGHTS if you want to greatly improve your front sight over that tiny little bead!!

Much better than the standard OEM bead. Installation was a breeze. You can use super glue if you don’t have JB Weld. I actually prefer the big dots without the tritium in the middle. They glow brighter, easier to see, and it’s half the price.

The sight is just what I wanted and expected...with one minor issue. The pros: The yellow sight takes very little ambient light to get it to glow, and it glows in the dark afterward. It's quite effective for what I needed, and I wanted the extra height (actual is .30"). Installation could be relatively easy, even though you have to clean the parts, barrel and epoxy the sight. I had one issue that's noted below. The con: Installing this on a Mossberg 500 required I use the included replacement bead. It appeared to be the correct thread but it had been cut through at the threads. It wasn't clean, easily fixable, nor beveled at the lead thread. The result was that I couldn't screw it in. Secondly, even if I could have used it, there was very little thread to work with. Comparing them, the threaded area of the XS bead was just a tad shorter than my Mossberg bead. The fix: I was getting ready for a trip. Rather than risk getting another like it from the vendor, I filed down/rounded the hex area of my Mossberg bead and then drill-widened the hole in the sight. Problem solved, though it took time and care to do it. I'm not suggesting this be the route to take. I'm just noting what I elected to do. To be fair, I didn't try to contact the vendor. Had my bead work not appeared adequate, before epoxying it, I would have contacted them. Lastly, for the Mossberg, I used a 4mm socket to remove my bead. I put masking tape against the face of the socket so as to not mar the barrel, and this worked perfectly. I've watched videos of others using small pliers and, having seen it happen, scratching the barrel is a real possibility. The bottom line is I really like the sight. It's not a true night sight unless it's been illuminated by light. Then it glows for some time after light is removed/shut off. I knew all that beforehand and only gave it four stars because of the bead I received.

This sight is absolutely awesome for the money. A quick blast with a high lumen flashlight and it gets super bright. Glows dimly if just kept around ambient light and you go into darkness. The sight is made completely of steel and comes with a replacement bead for mossberg shotguns. I used gorilla weld and a zip tie to install. Just make sure you clean the surfaces well with denatured alchohol to remove any oils from the barrel.

So, buyer beware, this is NOT a night sight. This is a LUMINESCENT front bead, i.e. a good old fashioned "glow in the dark" material NOT Tritium! You have to shine a bright light on the sight to "charge" it and make it glow. So, pretty useless for a defense sight at night. The font bead is big, and it is easy to pick up, and is pretty easy to install. This would be fine if it was advertised for what it really is. Definitely read the fine print! Since this gets epoxied on, its going to be a pain to get back off to replace with a proper night sight.

Huge improvement over the stock bead, and it fits the barrel perfectly. Even though i purchased the non tritium version, it is still very bright.. highly recommend!

My Mossberg came with a tiny brass bead. I upgraded to this for easier target acquisition. Installation was easy. Removed the old sight with socket. Cleaned the area (barrel and base of sight) to be glued with rubbing alcohol. Installed the bead that’s provided. Mixed JB Weld and filled the hole where the bead goes in the base of the sight and all the surface area of the base. Secured the base on the barrel with blue painters tape once I was content with the position of the sight. Waited 24hrs before I messed with the sight. It seemed rock solid.