ECOTRICStubby Front Bumper Compatible With 2007-2024 Jeep Wrangler JK JL Gladiator JT W/Fog Light Housing & D-rings Steel Powder Coated Black

ECOTRIC Front Bumper is indeed an invaluable asset, in fact, it can easily fit a custom setup like mine which is a C-10 wheeler! First it was made for Wranglers and Gladiators but after some minor modifications, it goes on my truck really well. The front bumper is very robust and stiff and can take a lot of abuse on rough terrain and most importantly, very good for the front end protection.The off-road bumper offers a rugged and aggressive look, which perfectly matches my off road setup. Moreover, the built-in winch plate and D-ring mounts are fantastic features that allow for easy recovery scenarios. In addition, it adds beauty but is also very practical as it’s highly resistant to rust and scratches – the powder-coated finish.In terms of fitment and modification, I’d say it was a struggle worth going through. This bumper completes the shape and function of my truck as it ready for the trails and also looks stunning. I would recommend this product to all the customizers out there; for adventurous drivers, this is an amazing product!

I have a 2014 Jeep Wrangler when I bought it it had the factory bumpers. I decided to upgrade to this bumper. It has a attachment on top which I didn't put on. But it was easy to install took about 15 minutes. It fits great and I love the look it was a great value compared to the rest of aftermarket bumpers.

This bumper is honestly the most inexpensive bumper I could find, probably cheaper than just a winch plate. For that alone, it is a tremendous value. It feels stout, I like the style, and there's no gaudy branding cut into it (I'm looking at you EAG). The hoop is a fat tube, and looks meaty (even though it's only attached via 8 small bolts).Cons... One of the d-ring mounts was welded crooked, so it looks kinda wonky, but with the shackle on it, it's not too noticable. The light tabs are a bit deep and low on the bar, so I'm unable to aim my Hella 500's down enough; I can probably correct with about a half inch stack of washers. I do wish there were some holes drilled into the tube to route wires, but I can punch my own. The package was pretty bad.. It was basically wrapped in felt and a 1/8" thick foam blanket, then cardboard wrapped around it (no airspace or cushioning). Amazingly, nothing was bashed in from shipping, but there were a couple (very minor) dents and scratched off paint on either side of where the winch mounts. No biggie, a dab of bed liner will hide it I'm sure. It doesn't come with nuts for the main mounting bolts, and I'm not sure if the factory nuts are compatible, but I ordered some from Amazon anyway (not here yet). But overall, I couldn't be happier with the value and appearance.I'm going to attempt to install onto a 2019 Wangler (JL), as rumor has it, JK bumpers are compatible. Will update when Amazon delivers the rest of my order.Edit: It fits JL Wranglers, no problem. There's maybe 1/2" gap between the bumper and the grille at the closest, so, no rubbing, looks like it was meant to be there. My Sport plastic bumper halogen fogs are the three-tab style, and this bumper takes the four tab style, so I had to drill a couple holes in the fogs to use them, but it worked out in the end. You'll need your own bolts to mount them. Hopefully there's no rubbing when the winch shows up.

Bumper looks incredible. Not going to lie to you, it was pretty hard to get the bumper itself onto the Jeep. Some of the bolts did not line up correctly, but after some hammer swings, a bunch of curse words, some cuts, and bruises, I finally got it on. As for the wiring of the bumper lights and fog lights, I used the factory fog light plug and just wired the lights to that positive to positive and negatives to the negatives. Works perfectly as you can see. Bumper lights turn off when you turn off the flog lights. It was easier than rewriting a whole new switch for the bumper lights. All in all, I’d buy from this seller again.

All this bumper has going for it is the looks. It is made from thin metal. A Badlands 12000 winch bolts directly to it. I will be adding an extra mounting plate to me 2011 Jeep Wrangler for a piece of mind that the bumper will not fail. The paint/finish will scratch easily. I found this to be true and I will be doing some touch ups. The box arrived damaged and the bumper was bent, I had to straighten the welded bolt in order to get in mounted.