Desertcart Logo

Q: So guys, I am using it on a M4 - M5 fasteners, where the goopy consistency covers the tiny threads too heavily. I wanted to wipe off excess although it sets almost immediately resulting in stringy mess, (although it does the job) do you have to cool the bolt or the VC3 liquid for best results? Also what kind of solve…

Those are some good questions my friend. Cooling the bolt is unnecessary, as it can be applied even under salt water, and it has cold flow properties to begin with. As far as solvents to clean it up, it's acrylic resin methyl ethyl ketone based , it stays in a taffy like consistency which never fully cures, it stays in a taffy like consistency, aka 'viscous resin'. Removing it can be done by picking or peeling it off. A couple times I used a small wire brush on my Proxxon rotary tool to remove Vc-3 on hard to reach inner threads. It's non soluble in water and also insoluble with many solvents, that's why it works so well with firearms when exposed to firearm nasty cleaning solvents such as Sweets Bore Cleaner and such. VC-3's anti vibration attributes keeps it put, it only comes off if that's your intend. It can be used as a thread 'dam' for damaged threads. It's so versatile, it'll also work on wood. I did gander through this products MSDS and Safety Data sheets to see if a specific cleanup agent is specified, but none listed, probably for the aforementioned reasons above. https://www.vibra-tite.com/wp-content/uploads/sds_-_VT213_-_Vibra-TITE%C2%AE_VC-3%C2%AE_US.pdf

Q: I have red thread locker, I think by loc tite. How does Vibratite red compare? Same chemistry different name?

Vibra-tite is more expensive and is more something for special purposes then Loc-tite is, You apply Vibri-titwe to the threads of a Bolt or Pipe Plug and you need to let it dry. It dries to sort of a rubbery coating in the Threads and you need to let it dry properly before you use it. Once it is dried you could put that Bolt on a shelf and come back Years later and use it and the Coating is good.If you have bought a Bolt or Plug from an Auto Parts Store and it has a Coating on it that is a Sealant or ant-vibration coating that is similar to Vibri-tite.The other feature of Vibri-tite is that you can remove the Bolt 2-3 times and do not have to re-coat the Bolt. You cannot do that with Loc-tite.I think Vibri-tite also can take a higher heat but you should check the Vibra-tite website for that. Loc-tite is sort of like plastic and it melts at a lower temp.In order for Loc-tite to be effective both surfaces need to be degreased (I use Brake Cleaner for that). With Vibra-tite the part you apply the coating to needs to be degreased but the other part can be Oily as long as the Oil is clean without a lot dirt sticking to it.It does not happen often but once in a while something you use Loc-tite on gets difficult to remove. While you can easily heat an area with a Propane Torch and melt Loc-tite; once melted you can remove the Bolt or Screw. Sometimes it is not possible to apply heat due to where the Part is. You will never have that problem with Vibra-tite.I was a Diesel Mechanic for 18 Years and I have used Loc-tite and similar generic thread lockers/sealers and the Vibri-tite. Most of the time I used Loc-tite. I thin like 95% of the time Loc-tite will do the job.If it is important enough I would go to the websites of the 2 Companies and get the details from them. The Company Loc-tite also makes different Products.Best Wishes

Q: how long does the opened container last before it dries out??

I opened and used the vibra threadmate tube 3 months ago on a lawn mower whose lower right bar attached by 3 screws came out. It was opened sporadically during a 30 minute period, totaling maybe 5 minutes of that 30 minutes of use. The 3 screws coated with the red gluish resin and screwed back in, have held up great. And unlike crazy glue's tube of glue, that oxidizes hard rather quickly (days, whatever) after brief exposure to air in opening the tube, I just opened the vibra threadmate tube again for your question and checked the red gluish like resin and it's still very fluid, which would stay like that in the tube, until placed on screws and dries around them. Though not to rock hard condition like with loctite for threaded screws back into their sockets. Loctite being for metal to metal and not metal to plastic like I needed it for, with the lawn mower. Vibra threadmate dries to a tough resin from its fluid resin condition and can be unscrewed a few times and screwed back in to still hold the screws in tightly. At least that is what is said about the red gluish resin. I haven't tried doing that.

Q: I apply on 5/8 bolt only on the threads where the nut goes, I wipe off excess. Takes 2 fairly big wrenches to assemble, am I putting too much?

Better to apply more than not enough to an open thread/nut, but if the thread lock is applied too much on a bolt that fits in to a closed ended solid metal block or frame, beware of hydrolic resistance.

交付 Malaysia

获得最佳体验获取应用程序

下载应用程序

我们从

阿联酋
英国
印度
美国
日本
KOREA

客户服务

关于我们

客户支持

有问题吗？看看别人问了什么

So guys, I am using it on a M4 - M5 fasteners, where the goopy consistency covers the tiny threads too heavily. I wanted to wipe off excess although it sets almost immediately resulting in stringy mess, (although it does the job) do you have to cool the bolt or the VC3 liquid for best results? Also what kind of solve…

I have red thread locker, I think by loc tite. How does Vibratite red compare? Same chemistry different name?

how long does the opened container last before it dries out??

I apply on 5/8 bolt only on the threads where the nut goes, I wipe off excess. Takes 2 fairly big wrenches to assemble, am I putting too much?

常见问题

产品是真实而真实的吗？+

是的，所有产品均直接来自美国，英国，阿联酋和印度的授权零售商。我们保持严格的质量控制过程，并在运输前验证每种产品。所有项目都有适用的制造商保证，并由我们的标准退货政策涵盖。

交货需要多长时间，这是可靠的？+

送货时间因目的地国家 /地区不等，通常从3-9个工作日不等。每个订单都可以通过我们的系统完全跟踪。我们处理所有关闭范围，并使用可靠的快递合作伙伴进行最后一英里的交付。您将通过电子邮件和我们的应用程序定期收到有关您的订单状态的更新。

什么是凡人车？从安全订购安全吗？+

自2014年以来，落伍车是一个国际电子商务平台。我们每天在全球范围内安全地处理数千个订单。每个产品都会在交付前经过我们的质量验证过程，我们提供端到端订单跟踪，24/7客户支持以及全面的回报政策，以确保安全的购物体验。

产品定价如何计算？+

我们的价格包括产品成本，国际运输，进口关税，关税和当地交货费用。我们处理所有海关和导入程序，确保交货时没有隐藏的费用。 Pro会员将获得额外的福利，包括免费送货。

RM539

关税和税费包括

Malaysia店铺

免费退货

30天对于 PRO 会员用户

15天无会员资格

安全交易

ChatGPT - opens in a new tab Perplexity - opens in a new tab Claude - opens in a new tab Grok - opens in a new tab Google AI - opens in a new tab

TrustPilot

TrustScore 4.5 | 7,300多个评论

维克拉姆·D.

MOLLE 护套质量非常好。我对这次购买非常满意。

2 周前

Reema J.

寻找稀缺商品的完美平台。送货及时。

1 个月前

查看所有TrustPiLot评论

Brand	Vibra-TITE
Manufacturer	Vibra-TITE
Country of Origin	USA
Model number	213
Item Weight	0.28 g
Product Dimensions	2.54 x 2.54 x 7.62 cm; 0.28 g
Item model number	213
Item Height	3 Inches
Item Width	1 Inches
Are batteries included?	No

Vibra-TITE VC-3 Threadmate, 30 ml Bottle with Brush Cap Applicator

描述

规格

有问题吗？看看别人问了什么

常见问题